Applied Instruments XR-3 Operation Manual Download | Manualshive

Page: 29 / 66

background image

XR-3 TS2 Module Operation Manual

XR-3

Page 29 of 66

3) Using the PC’s internet browser, access the HughesNet modem setup screens. Ensure that

the OPI display is enabled and display signal strength. The signal strength must be
displayed on the PC to generate the display shown on the meter.

4) Return to the dish and connect the XR-3 into the receiver cable. The XR-3’s ODU / LNB port

should be connected to the LNB and the IDU / IRD port to the modem’s Rx port.

5) Go to the XR-3 OPI/DiSEqC Screen. This screen displays the numbers transmitted from the

modem just like the OPI device.

6) Adjust the dish to peak the transmitter cross-pol quality number. The higher the number, the

better the quality.

DiSEqC Monitoring

When other DiSEqC commands are received on the IDU / IRD port of the meter, they are
displayed on the screen. The most common switch control commands are decoded into switch
type and port selection, other commands may be displayed in their hexadecimal format.

12. Bit Error Rate / Packet Error Rate

The Bit Error Rate / Packet Error Rate screen (select BER from the Main Menu) displays the bit
error rate (BER) or packet error rate (PER) of the signal as detected by the demodulator chipset
within the XR-3’s TS2 module.

TESCOM USA

TESCOMUSA.COM

«
...
27
28
29
30
31
...
»

Summary of Contents for XR-3



































































Reviews:

No comments

Related manuals for XR-3

Brand: LaMotte Pages: 2

Brand: 4iiii Pages: 3

Brand: XS Scuba Pages: 24

Brand: jablotron Pages: 2

Brand: LaMotte Pages: 2

Brand: Lampa Pages: 12

Brand: Wagner Meters Pages: 17

Level Pro UltraPro 500 Series

Brand: Icon Process Controls Pages: 19

Brand: SEAWARD Electronic Pages: 57

Brand: ScienTECH Pages: 44

Brand: BK Precision Pages: 21

Brand: Simpson Pages: 19

SUPER-CUTAWAY DIY ELECTRIC GUITAR KIT

Brand: Gear4music Pages: 24

Brand: YZ Systems Pages: 36

PROFESSIONAL II

Brand: EMU Pages: 24

Brand: Chauvin Arnoux Pages: 92

Brand: Sfere Pages: 22

IMI SENSORS 601A92

Brand: PCB Piezotronics Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands