Appion G5Twin Operation Manual Download Page 3

4

Warnings and Safety Information

IMPORTANT - READ THIS MANUAL BEFORE OPERATION

This Operation Manual contains important information for protecting your safety and preventing equipment 

problems. Unsafe operation could lead to serious injury or death to you or others. For best results and safe 

operation, read this entire manual before operation. Keep this manual in a safe, accessible location during 

operation.

 

WARNING

 

 

 When working with refrigerants, always use the appropriate Personal Protective Equipment 

(PPE), including 

eye and hand protection. Read all Material Safety Data Sheets (MSDS) for any compounds 

that you are likely to encounter during operation. Failure to do so could lead to injury or death.

OPERATOR TRAINING, CERTIFICATION AND RESPONSIBILITY

 

NOTICE

 

 

 This machine compresses and pumps liquid and vapor refrigerants at high pressures, which 

can create dangerous conditions. This equipment is for use by technicians that are professionally trained and 

certified in the safe handling of refrigerant, and safe refrigerant recovery techniques.

PERSONAL PROTECTIVE EQUIPMENT AND MSDS

HAZARD: RISK OF EXPLOSION OR FIRE

 

DANGER

 

 

 Use of this equipment may pose certain explosion and fire hazards.

WHAT CAN HAPPEN

HOW TO PREVENT IT

It is possible for electrical components within the 

unit to spark. If electrical sparks come into contact 

with flammable vapors, they may ignite, causing fire 

or explosion.

Use only in well ventilated areas. In enclosed areas, 

mechanical ventilation should provide at least four 

air changes per hour.

Flammable/combustible gases and air may become 

unknowingly ingested through leaks in hoses, 

gaskets, connections or leaking seals, leading to 

compression of these gases. Air and hydrocarbons, 

if pumped to a tank, create an explosive mixture 

that random static electricity could ignite.

Do not use in the vicinity of spilled or open 

containers of gasoline, propane, butane, acetylene, 

or other flammable gases.

Do not use near open sewer lines which may be 

emitting sewer gases.

Flammable substances may ignite or explode when 

compressed in certain situations.

Do not use this machine to pump hydrocarbons, 

including blends containing butane, isobutane, or 

propane. Hydrocarbons are flammable substances 

and may ignite or explode when compressed in 

certain situations. 

Improper use of extensions cords may result in 

overheating or fire in the cord or machine.

Use only 12AWG or 10AWG extension cords:

   -  Up to 25 Feet: 12/3 UL/CSA cord

   -  Up to 100 Feet: 10/3 UL/CSA cord

 

NOTICE

 

 

 Keep away from children at all times. Do not leave unattended.

 

NOTICE

 

 

 Never defeat the safety features of this product. Do not operate with missing, broken, or 

unauthorized parts. Remove broken or altered equipment from service immediately.

G5TWIN OPERATION MANUAL

© 2016 APPION INC. - ALL RIGHTS RESERVED 

Summary of Contents for G5Twin
























Reviews: