background image

21 

 
 

LIMITED TWO-YEAR WARRANTY 

 
 

Apollo Gate Operators are warranted against defects for a period of 

24 months from the date of purchase, providing recommended installation 
procedures are followed. This warranty is in lieu of all other warranties 
expressed or implied (some states do not allow limitations on how long an 
implied warranty lasts, so this limitation may not apply to you) and shall be 
considered void if damage was due to improper installation or use, 
connection to improper power source, or if damage was caused by fire, 
flood, or lightning. The manufacturer will not be responsible for any labor 
charges incurred in the removal or replacement of defective parts. 
 

In case of failure due to defective material or workmanship during the 

warranty period, the defective part will be repaired or replaced at the 
manufacturer’s option at no charge if returned freight prepaid. New or factory 
rebuilt replacements may be used. Replacement parts are warranted for the 
remaining portion of the original warranty period. The manufacturer will pay 
standard ground freight on the return of repaired or replaced items in 
warranty. 

APOLLO

 

Gate Operators, Inc. 

Summary of Contents for 7100ETL






















Reviews: