Apollo 7100ETL Installation Manual Download Page 11 | Manualshive

Page: 11 / 21

background image

11

CHAIN MAGNETS INSTALLATION

Align each magnet with the
corresponding switch on the
operator.

Connect the battery and adjust
the magnets for proper open &
close limits.

WARNING : Always disconnect
battery prior to relocating the
magnet.

Chain Path

Switch

Magnet

Switch

Magnet

Operator

Top View - Right Side

Front View

Switch

Magnet

Switch

Magnet

1.

2.

TIP:

If the gate automatically

opens after the close timer
expires, reverse the red &
black motor wires and reverse
the orange & white limit wires.

«
...
9
10
11
12
13
...
»

Summary of Contents for 7100ETL






















Reviews:

No comments

Related manuals for 7100ETL

Brand: Chamberlain Pages: 45

Brand: CAME Pages: 28

Brand: CAME Pages: 30

Brand: GDS Pages: 9

GDS 550P Series

Brand: GDS Pages: 15

Brand: GDS Pages: 17

Brand: GDS Pages: 17

Brand: Bauer Pages: 39

Brand: SOMFY Pages: 18

Dexxo Optimo RTS

Brand: SOMFY Pages: 58

Brand: B&D Pages: 20

Controll-A-Door 4

Brand: B&D Pages: 32

Brand: vds Pages: 49

AccessMaster M100

Brand: Chamberlain Pages: 36

Brand: Roger Technology Pages: 16

Brand: FAAC Pages: 24

Brand: Entrematic Pages: 4

Brand: Black & Decker Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands