API The BOX Operator'S Manual Download Page 59 | Manualshive

Page: 59 / 97

background image

API “The BOX”

Operator’s Manual

59

7.1.1 Aux Master Solos

Each aux master can be soloed using either the AFL or PFL solo mode.

When AFL is the current solo mode, mono aux masters 1 & 2 feed the LEFT and RIGHT
sides of the stereo AFL solo bus in mono. Stereo aux master 3-4 feeds the output of
aux bus 3 to LEFT and aux bus 4 to RIGHT. The AFL solo bus is fed immediately after
the aux master potentiometers.

When PFL is the current solo mode, mono aux masters 1 & 2 feed the mono PFL solo
bus in mono. The stereo aux master 3-4 outputs are summed together and fed to the
PFL  solo  bus  in  mono.  Even  though  the  console  is  in  PFL,  the  PFL  solo  bus  is  fed
immediately after the AUX MASTER potentiometers.

NOTE: When solo-in-place (SIP) is the current solo mode, engaging an aux master

AFL SOLO switch will activate the current PFL or AFL solo function. The solo
function is determined by the position of the AFL switch in the solo master
section. Engaging an aux master AFL SOLO while in SIP mode will not active
SIP mutes on channels.

7.2 Auxiliary Master Rear Panel Connections

AFL SOLO: Activates the AFL or PFL solo function when engaged

•

Labeled AFL because the selected solo bus is always fed after
the aux master pot (no PFL solo function on aux masters)

•

Can be cleared by pressing the SOLO CLEAR button

•

Illuminates when engaged

AUX OUTPUTS / CUE OUTPUTS: DB-25, balanced,
low-impedance, line-level

•

Fed from the aux and cue masters

•

Standard pin-out:

1-4=aux outputs 1-4,

5-6=cue outputs L-R

•

«
...
57
58
59
60
61
...
»

Summary of Contents for The BOX


































































































Reviews:

No comments

Related manuals for The BOX

Brand: Vitek Pages: 40

Brand: Beper Pages: 64

Brand: Nady Audio Pages: 15

Brand: Ratek Pages: 16

Brand: Hotone Pages: 2

Brand: DAPAudio Pages: 18

Brand: Cloud Pages: 10

Brand: Kambrook Pages: 20

Pasta Prof PL10S

Brand: R.G.V. Pages: 52

Analog Custom Shop Blues Overdrive

Brand: Akai Pages: 2

Brand: Hkoenig Pages: 77

Brand: Sealey Pages: 2

Brand: SEIKAKU Pages: 11

Tube Screamer TS-808

Brand: Ibanez Pages: 4

Brand: Ninja Pages: 2

Brand: Gemini Pages: 6

Brand: Lithium Grim Pages: 7

Little Sultan of Tone

Brand: Lithium Grim Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands