API The BOX Operator'S Manual Download Page 39 | Manualshive

Page: 39 / 97

background image

API “The BOX”

Operator’s Manual

39

3.4.2 Stereo Aux Send 3/4

AUX  3/4  is  a  stereo  auxiliary  send  that  feeds  aux  buses  3  and  4  by  default.  These
sends  can  also  be  routed  to  the  stereo  cue  bus  to  quickly  create  a  fully  featured
headphone feed when recording. When mixing, stereo AUX 3/4 or CUE can be used for
effects sends.

A  common  on/off  switch  is  used  to  silently  engage  the  stereo  send.  The  post-fader
signal  feeds  AUX  3/4-CUE  by  default,  but  the  pair  can  be  switched  to  the  pre-fader
signal. In common practice, post-fader sends are often used for effects sends and pre-
fader sends are typically used for headphone feeds.

3.4.3 Stereo Cue Sends

In addition to auxiliary buses 1-4, “The  BOX”  is equipped with a separate stereo cue
bus,  cue  master,  and  balanced  output.  When  recording,  the  primary  purpose  of  this
cue system is the creation of a headphone feed, so talkback and other sources can be
routed to the cue master. When mixing, stereo send 3/4 can be routed to the cue bus
instead of aux buses 3/4 to provide an alternate stereo effects send.

AUX 1-AUX 2: Level controls for AUX 1/2

•

Knob = 1, ring = 2

PRE (pre-post): Routes the pre-fader signal to
AUX 1/2 when engaged

•

AUX 1/2 are fed post-fader by default

•

Illuminates when engaged

1/2 (on/off): On/off switches for AUX 1/2

•

Illuminates when engaged

AUX 3/4: Level controls for AUX 3/4 or CUE

•

Knob = level, ring = pan

PRE (pre-post): Routes the pre-fader signal to
AUX 3/4-CUE when engaged

•

AUX 3/4-CUE are fed post-fader by default

•

Illuminates when engaged

3/4 (on/off): On/off switches for AUX 3/4-CUE

•

Illuminates when engaged

CUE: Routes aux send 3/4 to the stereo cue bus when engaged

•

AUX 3/4 feeds auxiliary buses 3 and 4 by default

•

The feed to auxiliary buses 3 and 4 is defeated when engaged

•

Illuminates when engaged

«
...
37
38
39
40
41
...
»

Summary of Contents for The BOX


































































































Reviews:

No comments

Related manuals for The BOX

Brand: STK Professional Audio Pages: 28

Noise Reducer NR300

Brand: Behringer Pages: 32

Brand: TECHWOOD Pages: 11

Brand: Oceanic Pages: 16

Clean Blade Boost

Brand: Lithium Grim Pages: 8

Brand: Harman Pages: 56

Brand: Wassermann Dental-Maschinen Pages: 16

Brand: Tapco Pages: 28

SansAmp PSA 2.0

Brand: tech21 Pages: 12

Brand: Fender Pages: 14

Brand: digico Pages: 23

Brand: GPX Pages: 2

Brand: Sound Devices Pages: 60

Brand: Russell Hobbs Pages: 8

Brand: Harbinger Pages: 16

Brand: Harbinger Pages: 20

Brand: Xvive Pages: 2

Brand: Citronic Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands