background image

Page 3

AM

ER

IC

AN

 P

ILE

DRIVING E

QU

IP

M

EN

T

 J&

M

  F

O

UN

DAT

ION  EQ

UIP

M

EN

T

800-248-8498

800-248-8498

WWW.AMERICANPILEDRIVING.COM

WWW.AMERICANPILEDRIVING.COM

MODEL 300-4 VIBRO

Copyright © 2020 American Piledriving Equipment Inc. All Rights Reserved

1. 

Read and follow any safety instructions in the 

Excavator operators manual. 

2. 

Only well-trained and experienced personnel 

should operate or maintain this equipment.

3. 

Do 

NOT

 

adjust, lubricate or repair the unit when 

it is in operation or lifted above ground level.

4. 

Do 

NOT 

remove, paint over and/or cover 

warning or safety labels. If labels become 

damaged or unreadable, replace immediately.

5. 

All personnel should wear approved safety 

clothing, including HARD HATS, SAFETY 

SHOES, SAFETY GLASSES and HEARING 

PROTECTION when near this equipment.

6. 

Do 

NOT

 stand close to this equipment when it 

is in operation. Dirt and parts may fall. 

NEVER

 

stand under operating or elevated equipment. 

Keep your eyes on the hammer while it is in 

operation.

7.  When maintaining and/or repairing the 

equipment, 

NEVER

 substitute parts not 

supplied or approved in writing by APE.

Do 

NOT

NOT

 weld or flame cut on this 

equipment.

8. 

Do 

NOT 

use or store flammable liquids on or 

near the engine.

9.  Ensure that all lifting equipment, including 

cranes, wire rope, slings, hooks, shackles, etc., 

are properly sized for the worst case loads 

anticipated during operations.

10. If there are any questions about the weights, 

specifications or performance of the unit, 

contact APE before handling and/or operating 

the equipment. 

11. Check wire rope clips for tightness and wire 

ropes for wear daily. 

When operating in an enclosed 

area, exhaust fumes should be 

piped outside.

Continued breathing of exhaust 

fumes may prove 

FATAL

.

12. Ensure that ground vibrations will not damage 

or collapse adjacent structures or excavations. 

(These precautions must be followed at all times to ensure personal and equipment safety.)

DANGER indicates a hazardous situation which, if not 

avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if not 

avoided, could result in death or serious injury.

CAUTION indicates a hazardous situation where 

injury could occur but is unlikely to be serious or 

lead to death. 

NOTICE indicates information that may help or guide you 

in the operation or service of the equipment. 

DISCLAIMER

This unit was tested and flushed before leaving our 

facility. In order to help provide years of trouble free 

usage, please review the following documentation and 

make sure to clean and flush the field piping before 

connecting it to the power unit.

Refer to schematic diagrams and the BOM (Bill of 

Materials) for component part specifications and 

recommended spare parts.

When calling APE (American Piledriving Equipment), 

always inform them of the supplied serial # in order to 

obtain quicker service.

Read this manual thoroughly before 

operating and / or working on the 

equipment. 

Summary of Contents for Vibro 300-4





































Reviews: