background image

TABLE OF CONTENTS

 

CARE & SAFETY PRECAUTIONS ……………...…….. 3  

PRODUCT DESCRIPTION …………………….……… 4 

FUNCTIONS & FEATURES …………….……………… 4 

PACKAGE INCLUSION ……………….……………..  5 

SPECIFICATIONS ………………………..……………. 5 

OPERATING PROCEDURES ………………...…...  6-11 

BASIC TROUBLESHOOTING GUIDE …………….... 12  

This appliance can be used by children aged from 8 years and above and persons with reduced 
physical, sensory or mental capabilities or lack of experience and knowledge if they have been 
given supervision or instruction concerning use of the appliance in a safe way and understand the 
hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall 

not be made by children without supervision. 
 
The specific instructions related to the safe operation of this appliance (as given in 7.12 of this 
standard) shall be collated together in the front section of the user instructions. 
The height of the characters, measured on the capital letters, shall be at least 3 mm. 
These instructions shall also available in an alternative format, e.g. on a website. 

 

A fire may result if the appliance is not used with care, therefore: 

→ 

be careful when using the appliance in places where there are combustible materials ; 

→ 

do not apply to the same place for a long time; 

→ 

do not use in presence of an explosive atmosphere; 

→ 

be aware that heat may be conducted to combustible materials that are out of sight; 

→ 

place the appliance on its stand after use and allow it to cool down before                                           
storage; 

→ 

do not leave the appliance unattended when it is switched on. 

 

Rohs  

Correct Disposal of this product 

This marking indicates that this product should not be disposed with 
other household wastes throughout the EU. To prevent possible harm 
to the environment or human health from uncontrolled waste 
disposal, recycle it responsibly to promote the sustainable reuse of 

material resources. To return your used device, please use the return 
and collection systems or contact the retailer where the product was 
purchased. They can take this product for environmental safe 
recycling.

 

 

 

 

11  

 

 

 

OPERATING PROCEDURES 

 
Note:
There is a built in protection feature to automatically limit the 
temperature rising slope to no more than 3 degrees per second. Therefore 
based on your set time, the maximum temperature may not reach 250C. 
Sample Profile analysis: 
SEG1          SEG2         SEG3         SEG4         SEG5          SEG6 
050t           060t           080t          050t          040t             60t 
100C          150C          180C         190C         195C           100C 
 
Segment one is set to 50 seconds to reach 100C. Which means after 
50seconds at the end of segment one the temperature should reach 100C. 
Then Segment two is set to 60 seconds to reach 150C, which means by 
the end of 60 seconds the set temperature should reach 150C, so on and 
so forth.  
 
To check the slope from segment Two : 

● 

150C - 100C =50C 

● 

Time to reach 150C is set to 60seconds. 

● 

Therefore the slope is 50/60= 0.833 degrees per second increase. 

 
To determine the slope if it is declining as seen in segment six: 

● 

195C - 100C =95C 

● 

Time to reach 100C is set to 60seconds. 

● 

Therefore the slope is 95/60= 1.58 degrees per second decline. 

 
Recommended Working Profile : 
SEG1          SEG2         SEG3         SEG4         SEG5          SEG6 
060t           060t           060t          050t          040t             30t 
100C          130C          150C         172C         180C           180C 

Summary of Contents for Int883







Reviews: