background image

-B281*B02U*CC20  4/17-

×

×

×

Connection targets

Specifications

Model

Functions

Functions

Address

*

1  It depends on lot No. whether this function is available or not.

*

2  This terminal can be used in connection to the AnyWireASLINK unit for word transmission. Note that this terminal cannot handle word data by setting a word address.

*

3  To use these functions, a master unit that supports each function is required. For details, refer to the manual for the master unit together with this manual.

[Functions]

Bit 

transmission

ASLINKER
2-wire 
(non-isolated) 
cable type

General-purpose 
sensors, switches
General-purpose 
output devices

Detection of sensor cable 

disconnection

2-wire type 

sensor

3-wire type 

sensor

Bit 

address 

setting

Slave unit voltage 

drop

Sensing level drop

I/O disconnection

I/O short-circuit

I/O power supply 

drop

Word 

address 

setting

Function list

Detecting functions (Status details) 

NPN input: 2 points, 
NPN output: 2 points
NPN input: 1 point/output: 1 point
PNP input: 2 points,
PNP output: 2 points
PNP input: 1 point/output: 1 point

Function

*

4  This terminal can be used in connection to the AnyWireASLINK unit for word transmission. Note that this terminal cannot handle word data by setting a word address.

*

5  The single unit simplified replacement function works even if the lot No. does not support the LED indication for the single unit simplified replacement function.

 

(When the master unit executes the single unit simplified replacement function, addresses/parameters will be written, if specified conditions are satisfied.)

Lot No. is indicated on the lot label.

Example:

How to check

Word transmission

*

4

Remote address change
Single unit simplified replacement

S/W version

Function version

H/W version

LED indication for single unit 
simplified replacement function

*

5

Lot No.

This unit has undergone addition of functions and change of specifications according to version upgrading. 
Available functions and specifications of the unit vary depending on lot No.

[Function Compatibility by Lot No.]

Lot No. 19ECBNB

Back of this unit 

Available with S/W version “B” or later version
(If lot No. is indicated in 3 digits (year and 
month only), these functions are not available.)

Available with lot No. that indicates year and 
month digits of “15J” or later

Single unit 

simplified 

replacement

Remote 

address 

change

*

1

*

2

*

1

*

3

*

1

*

3

 Word

 

transmission

Summary of Contents for B281-B-02U-CC20 Series


















Reviews: