background image

-B281*B02U*CC20  2/17-

A

1

B

2

C

3

D

4

E

5

F

6

G

7

H

8

I

9

J

10

K

11

L

12

Lot No. 19ECBNB

As a result of the addition of functions, indication of lot No. has been changed from 3 digits (conventional format: 
year and month only) to 6 digits or 7 digits.

The master unit compatible with the word transmission function provides areas for transmission and receiving of word 
data (numerical information) such as analog data and sensing level data.
Using this function enables reduction of occupancy of bit information area by word data.
To enable word transmission, it is necessary that the system should be configured only with slave units compatible with 
the word transmission function.
A slave unit incompatible with the word transmission function cannot be connected to the AnyWireASLINK system to 
conduct word transmission.
For slave units that handle word data, word address settings are required.

[About AnyWireASLINK Ver. 1.1]

[About Lot No.]

[About Word Transmission]

*

3  Some products have no indication of function version.

Year: Numbers
 

(Lower two digits of the Christian era)

Month: Alphabet (as per the table below)

“19E” means May 2019.

Single unit simplified replacement

*

1

Word transmission

*

1

*

2

Functions available with Ver. 1.1

*

1  To use these functions, the master unit compatible with each function is required.

 

For details, refer to this manual together with the manual for the master unit.

*

2  You can use this function with the word-transmission AnyWireASLINK unit connected.

 

To handle word data, word address settings are required for slave units.

 

It depends on slave units whether word address setting is enabled or not.

New functions have been added to AnyWireASLINK products in May 2019 onward. Also, for the purpose of 
differentiation of compatible functions, indication of product lot number (lot No.) has been changed.

Compatible functions vary depending on lot No. Please understand the following description thoroughly to use each 
product.

Functions added to Ver. 1.1 are as follows:

Example:

S/W version

Year and month

H/W version

Alphabet

Month

Function version

*

3

Summary of Contents for B281-B-02U-CC20 Series


















Reviews: