background image

 

 

ACT-5X+ Exciter User Manual 

Version 1.1 5/8/2015 

 

Page 4 of 33 

 

 

 

WARNING 

THE  VOLTAGES,  CURRENTS,  AND  RF  ENERGY  IN  THIS  EQUIPMENT  ARE 
DANGEROUS.  PERSONNEL  MUST  AT  ALL  TIMES  OBSERVE  ALL  SAFETY 
WARNINGS, INSTRUCTIONS, AND REGULATIONS. 
 
IN  THE  CASE  OF  EMERGENCY,  ENSURE  THAT  ALL  POWER  HAS  BEEN 
DISCONNECTED.   
 
ALWAYS 

DISCONNECT 

POWER 

BEFORE 

REMOVING 

COVERS, 

ENCLOSURES,  OR  SHIELDS.  DO  NOT  PERFROM  SERVICE  ON  THE 
EQUIPMENT  WHEN  ALONE  OR  FATIGUED.  KNOW  YOUR  EQUIPMENT  AND 
DO NOT TAKE RISKS. 
 

This manual is provided as a general guide for trained and qualified personnel well aware of 
the dangers inherent in handling potentially hazardous electrical transmission equipment.   
 
The installation, operation, maintenance and service of this equipment involves risks both to 
personnel  and  equipment,  and  must  ONLY  be  performed  by  qualified  personnel  exercising 
due care. Anywave Communication Technologies, Inc. shall not be responsible for injury or 
damage  resulting  from  improper  handling  or  from  the  use  of  improperly  trained  or 
inexperienced personnel performing such tasks. 
 
All local building and electrical codes as well as fire protection standards must be observed in 
the installation and operation of the equipment. 

Summary of Contents for ACT-5X+


































Reviews: