background image

 

 

ACT-5X+ Exciter User Manual 

Version 1.1 5/8/2015 

 

Page 2 of 33 

 

 

 

Copyright Notice 

Copyright © Anywave Communication Technologies, Inc. 2014, All rights reserved. 
No  part  of  this  publication  may  be  reproduced,  translated,  transcribed,  stored  in  a  retrieval 
system, or transmitted into any form or by any means, without the express written permission 
of Anywave Communication Technologies, Inc. 

 

FCC Compliance 

This  equipment  complies  with  relevant  portions  of  Parts 2,  73,  &  74 of  the  FCC  rules 
governing LPTV operation. 
 

Disclaimer 

Information  provided  by  Anywave  Communication  Technologies  is  believed  to  be  accurate 
and complete; however, no liability can be assumed for its use.   
 
The manufacturer makes no representations or warranties, either expressed or implied, by or 
with respect to anything in this manual, and shall not be liable for any implied warranties of 
fitness  for  a  particular  purpose  or  for  any  indirect,  special,  or  consequential  damages. 
Information  in  this  document  is  subject  to  change  without  notice  and  does  not  represent  a 
commitment on the part of the manufacturer. 

 

USE  OF  THIS  PRODUCT  IN  A  MANNER  OTHER  THAN  DESCRIBED  IN  THIS 
MANUAL  MAY  RESULT  IN  DAMAGE  TO  THE  EQUIPMENT  AND/OR  PERSONAL 
INJURY.   
 
PLEASE  READ  THIS  MANUAL  IN  ITS  ENTIRETY  BEFORE  ATTEMPTING  TO 
INSTALL  THE  EQUIPMENT.  CONTACT  ANYWAVE  WITH  ANY  QUESTIONS  OR 
CONCERNS YOU MAY HAVE. 

 

 

 

 

Anywave Communication Technologies Inc. 
300 Knightsbridge Parkway, Suite 150, Lincolnshire, IL 60069

 

Tel: (847) 415-2258

 

Fax: (847) 415-2112

 

http://www.anywavecom.com/en/

 

Summary of Contents for ACT-5X+


































Reviews: