manualshive.com logo in svg

Antunes VCT-1000 Series, Owner'S Manual, Page: 8 / 22

Share
Download
Antunes VCT-1000 Series Owner'S Manual Download Page 8

8

P/N 1010807 Rev. Q 09/18

®

Figure 6. 

Removing Optional Belt Wrap

Interlock 

Switch  

(Some Models)

Conveyor 

Cover Assy.

Belt Wrap 

Pin

Conveyor Belt 

Chains

NOTICE

Align the ends of the Belt Wrap properly (Figure 8) or the 

Belt Wrap may be damaged.

NOTICE

Position the Belt Wrap inside the upper and lower yellow 

support rods or damage to the unit may occur.

Checking the Conveyor Belt 

Chains

NOTICE:

 The Bun Thickness Compres-

sion Knobs (Figure 4) must be 

set to “6 & 6” or “6 & F” prior 

to measuring or removing or 

reinstalling the Conveyor Belt 

Chains.

Measuring Conveyor belt Chains

1. 

Turn the unit off, unplug the power 

cord, and allow the unit to cool.

2. 

Remove the Bun Feeder, Butter 

Wheel, Pan, and Heat Shield (Figure 

1) and set the Bun Thickness Com-

pression Knobs to 6 & 6 or 6 & F.

3. 

Open both Conveyor Covers and pull 

the Belt Wrap Pin out of the zipper 

(Figure 6).

4. 

Remove the Belt Wrap.

5. 

Facing the toaster, locate the approxi

-

mate center-point of the Conveyor 

Chain.

6. 

Pull the Conveyor Chain away from 

the edge of the toaster (Figure 9). 

7. 

Stand a U.S. Dime on end between 

the frame and the chain (Figure 9). 

8. 

If the gap is significantly wider than 

the coin, REMOVE links as described 

below.

9. 

Disconnect the Conveyor Belt Chain 

by squeezing any two links together 

and unhooking both ends one link 

(Figure 10). Needle-nose pliers may 

be used.

NOTICE:

 There are two small 1/2” links 

on each side of the Conveyor 

Belt Chain. The rest are large 

3/4” links.

10. 

Remove one 1/2” link from the belt.

11. 

Reassemble the Conveyor Belt Chain 

onto the sprockets as described in 

Replacing Conveyor Belt Chains.

12. 

Measure the gap again to ensure it is 

not too tight.

13. 

Check the opposite side of the toaster 

using the same steps.

NOTICE:

 If the Conveyor Belt Chain 

is too tight to be reassembled, 

remove an additional small 1/2” 

link and install a large 3/4” link 

in its place.  This will shorten 

the Conveyor Belt Chain by 1/4” 

overall.  

CAU

TIO

N

Belt Wrap 

Pin

Upper Support Rod

Lower Support 

Rod

Figure 7. 

Installing Belt Wrap

INCORRECT

CORRECT

Figure 8. 

Aligning Belt Teeth

Summary of Contents for VCT-1000 Series























Reviews:

No comments