manualshive.com logo in svg

Antunes VCT-1000 Series, Owner'S Manual, Page: 10 / 22

Share
Download
Antunes VCT-1000 Series Owner'S Manual Download Page 10

10

P/N 1010807 Rev. Q 09/18

®

WARNING

To avoid possible personal injury and/or damage to the unit, inspection, test and repair of electrical equipment should be performed 

by qualified service personnel.  The unit should be unplugged when servicing, except when electrical tests are required.  Use ex

-

treme care during electrical circuit tests.  Live circuits will be exposed.

Troubleshooting

Problem

Possible Cause

 Corrective Action

No heat and Conveyor Belt 

Chains do not move.

Toaster is installed incorrectly.

Perform the installation and operating procedures found 

in the Installation and Operation sections of this manual.

Inoperable Power Cord or Power Switch.

Check receptacle for correct voltage (see the 

Specifications section of this manual).

If necessary, contact your maintenance person or 

Authorized Service Agency for service.

Hi-Limit Control is tripped.

Reset the Hi-Limit Control (see Figure 6 in the 

Operations section of this manual).

Wiring problem.

Contact your maintenance person or Authorized Service 

Agency for service.

No heat but Conveyor Belt 

Chains move.

Wiring problem. 

Contact your maintenance person or Authorized Service 

Agency for service.

Inoperative Platen.

Inoperable Thermostat

Platen is hot but Conveyor 

Belt Chains do not rotate.

Heat Shield not installed.

Install Heat Shield (Figure 2).

Conveyor Safety Interlock Switch (if 

present) not activated by the Heat Shield.

Re-install the Heat Shield correctly so that the Heat 

Shield applies appropriate pressure on the Conveyor 

Safety Interlock Switch. If the Interlock Switch has failed, 

order kit 7001436 to remove and bypass the Interlock 

Switch.

Spring Tensioner Assembly or Roller 

Tensioner is damaged or missing.

Replace Spring Tensioner or Roller Tensioners if 

damaged or missing.

Conveyor Belt Chain links too loose.

Adjust Conveyor Belt Chain length as described in the 

Maintenance section of this manual.

Inoperable Drive Motor.

Contact your maintenance person or Authorized Service 

Agency.

Loose Drive Motor Sprocket Setscrew.

Drive Motor Chain has fallen off sprocket(s).

Inoperable Safety Interlock Switch.

Conveyor Belts Chains 

hesitate to rotate and/or 

skip on sprockets.

Conveyor Belt Chains installed  

incorrectly.

Install Conveyor Belt Chains to match Figure 11.  Be 

sure that the ends of the hooks are facing down.

Conveyor Belt Chains too loose.

Adjust Conveyor Belt Chain length as described in the 

Maintenance section of this manual.

Spring Tensioner Assembly or Roller 

Tensioner is damaged or missing.

Replace Spring Tensioner Assembly or Roller 

Tensioners if damaged or missing.

Summary of Contents for VCT-1000 Series























Reviews:

No comments