background image

LIMITED WARRANTY

Equipment manufactured by Roundup Food Equipment Division of A.J. Antunes & Co. has been constructed of the finest materi-
als available and manufactured to high quality standards. These units are warranted to be free from electrical and mechanical 
defects for a period of one (1) year from date of purchase under normal use and service, and when installed in accordance with 
manufacturer’s recommendations. To insure continued operation of the units, follow the maintenance procedures outlined in the 
Owner’s Manual. During the first 12 months, electro-mechanical parts, non-overtime labor, and travel expenses up to 2 hours (100 
miles/160 km), round trip from the nearest Authorized Service Center are covered.

1. This warranty does not cover cost of installation, defects caused by improper storage or handling prior to placing of the Equipment. 

This warranty does not cover overtime charges or work done by unauthorized service agencies or personnel. This warranty does 
not cover normal maintenance, calibration, or regular adjustments as specified in operating and maintenance instructions of this 
manual, and/or labor involved in moving adjacent objects to gain access to the equipment. This warranty does not cover consum-
able/wear items. This warranty does not cover damage to the Load Cell or Load Cell Assembly due to abuse, misuse, dropping of 
unit/shock loads or exceeding maximum weight capacity (4 lbs). This warranty does not cover water contamination problems such 
as foreign material in water lines or inside solenoid valves. It does not cover water pressure problems or failures resulting from 
improper/incorrect voltage supply. This warranty does not cover Travel Time & Mileage in excess of 2 hours (100 miles/160 km) round 
trip from the nearest authorized service agency. 

2. Roundup reserves the right to make changes in design or add any improvements on any product. The right is always reserved to 

modify equipment because of factors beyond our control and government regulations. Changes to update equipment do not con-
stitute a warranty charge.

3. If shipment is damaged in transit, the purchaser should make a claim directly upon the carrier. Careful inspection should be made of the 

shipment as soon as it arrives and visible damage should be noted upon the carrier’s receipt. Damage should be reported to the carrier. 
This damage is not covered under this warranty.

4. Warranty charges do not include freight or foreign, excise, municipal or other sales or use taxes. All such freight and taxes are the 

responsibility of the purchaser. 

5. THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED 

WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, EACH OF WHICH IS HEREBY EXPRESSLY DIS-
CLAIMED. THE REMEDIES DESCRIBED ABOVE ARE EXCLUSIVE AND IN NO EVENT SHALL ROUNDUP BE LIABLE FOR SPECIAL CON-
SEQUENTIAL OR INCIDENTAL DAMAGES FOR THE BREACH OR DELAY IN PERFORMANCE OF THIS WARRANTY.

+1 (630) 784-1000

+1 (800) 253-2991

+1 (630) 784-1650

+86-512-6841-3907

+400-0-7878-22

+86-512-6841-3637

Summary of Contents for MS-150

















Reviews: