Antunes 9210912 Owner'S Manual Download Page 8

Page: 8 / 20

Viewing Settings

To view the toaster settings press and

hold the Menu button (Figure 4) for

approximately 5 seconds. The unit beeps

and shows the settings in the following

order, displaying the value in column 1

first, then the actual setting.

Display

Shows

Setting Description

ºA -

° F

Platen current

temperature*

bº -

° F

B Auxiliary heater current

temperature*

SPEd

Speed of belts

Unit

Current temperature Unit

Error Code

Et - d

Elapsed Time of toaster

usage

Int

° F

Internal toaster

Temperature

Power Line Voltage

* The first circles shown in these values

represent the Platen indicator lights. The

temperature unit will be shown as ° F or °

C depending on the Unit setting.

Changing Settings

The only settings that can be changed on

the toaster are:

Platen setpoint temperature

Auxiliary setpoint temperature

Speed

Unit

To change these settings:

With the toaster turned off, press and

hold the Menu button and turn the

toaster on. Continue holding the Menu

button until the unit beeps and EnA

appears on the display. Release the

Menu button.

Press the Menu button again. The

toaster shows ºA - ° F (Platen) and

then shows the current Platen setpoint

value. Use the ▲ and ▼ buttons to

change the value as needed.

Press the Menu button to move to the

Auxiliary setting. Edit as needed.

Press the Menu button to move to the

SPEd (Speed setting). Edit as needed.

Press the Menu button to move to the

Unit setting. Edit as needed.

The settings are saved each time you

press the Menu button and move to the

next value. The toaster exits programming

mode after 30 seconds of inactivity.

Figure 4.

Control Panel and Display

Display

Down Arrow Button

Up Arrow Button

Button

Factory Reset

To reset the toaster to the original factory

settings:

Turn the toaster off.

Press and hold both the ▲ and ▼

buttons and turn the toaster on,

continuing to hold the ▲ and ▼

buttons until the unit beeps and

FR (Factory Reset) appears on the

display.

Release the buttons.

Hi-Limit Reset Button

A Hi-Limit Control turns off power to the

unit if it overheats. To reset the control,

allow the unit to cool, then locate the Reset

Button at the rear of the unit. Remove

the black protective cap, press the Reset

Button, and reinstall the protective cap

(Figure 3).

NOTE:

If the Hi-Limit requires

continuous resetting, contact

Antunes Technical Service.

P/N 1011376 Rev. D 11/20

Summary of Contents for 9210912





















Search results

Summary of Contents for 9210912

Reviews:

Related manuals for 9210912

Brands by name

Popular brands

Antunes 9210912, Owner'S Manual

Search results

Summary of Contents for 9210912

Reviews:

Related manuals for 9210912

Brands by name

Popular brands