background image

Overview

This unit is intended to be used for com-

mercial applications, for example: in kitch-

ens of restaurants, canteens, hospitals and 

in commercial enterprises such as baker-

ies, butcheries, etc., But not for continuous 

mass production of food.

Before Use

This manual contains safety, installation, 

and operating procedures for the unit. 

Read and understand it completely before 

installing or operating the unit. Keep this 

document for reference. If the unit changes 

ownership, this manual must accompany it.

In Case of Damage

If the unit arrives damaged, file a claim 

with the carrier immediately. Save all pack-

ing materials when filing a claim. Freight 

damage claims are the responsibility of 

the purchaser and are not covered under 

warranty.

Website

www.antunes.com

Service/Technical 

Assistance

In Case of Damage

If any parts are missing or damaged, 

problems with the installation or operation 

of this product contact Antunes Customer 

Service immediately at +1-877-392-7856 

(toll free).

Fill in the information in the next section 

and have it ready when calling for 

assistance. The serial number is on the 

specification sticker located on the system.

Equipment Information to Save

Purchased from:

Date of purchase:

Model number:

Serial number:

Manufacturing number:

Authorized Service Agency

Name:

Phone No:

Address:

Table of Contents

Overview 2

Before Use 

2

In Case of Damage 

2

Website 2

Service/Technical Assistance 

2

In Case of Damage 

2

Equipment Information to Save 

2

Authorized Service Agency 

2

Safety Information Page 

3

Installation 3

Operation 3

Maintenance 3

Service 3

Specifications 

4

Electrical Ratings 

4

Electrical Cord & Configurations 

4

Dimensions 4

Installation 5

Unpacking 5

Equipment Setup 

5

Installing the Bun Chute 

5

Operation 6

Recommended Temperatures 

6

Recommended Speed Setting 

6

Light/Dark Setting 

6

Hi-Limit Reset Button 

6

Viewing Settings 

7

Changing Settings 

7

Factory Reset 

7

Maintenance 8

Daily Cleaning 

8

Quarterly Cleaning 

9

Replacing the Belt Wraps 

10

Checking the Conveyor Belt Chains   11

Measuring conveyor belt Chains 

11

Replacing Conveyor Belt Chains 

11

Fault Codes 

12

Troubleshooting 13

Replacement Parts 

14

Exploded Views 

16

Wiring Diagram 

20

Notes 21

Limited Warranty 

23

®

P/N 1011376 Rev. D 11/20

2

Summary of Contents for 9210912





















Reviews: