background image

Anthony Liftgates, Inc. 

 

ETU Maintenance

www.anthonyliftgates.com  

800-482-0003

1. General 

Information

1.1 Introduction

Congratulations on selecting an Anthony Liftgates 
TuckUnder™ liftgate.

All Anthony tuckunder model liftgates are factory 
assembled, energized, and tested to ensure the 
highest quality performance standards.  ETU liftgates 
ship completely assembled for fast, clean, and easy 
installation. 

To ensure your liftgate will perform to your expectations, 
we have provided this Installation Manual, which is 
designed to provide you with the necessary installation 
instructions and safety precautions for the installation of 
the ETU TuckUnder™ liftgates.

Typical Anthony Liftgates ETU Tuckunder Model.

1.2 General 

Safety

WARNING

Read, Understand, and 

Follow the Manual 

 

The success or failure of 

this liftgate to properly and efficiently operate depends 
on an ongoing preventative maintenance program. 

 

Failure to read, understand, and follow the maintenance 
instructions and safety recommendations in this 
manual can result in serious injury or death.

Also, read and understand the operating instructions 
in the separate Operation Manual before performing 
any maintenance. 

1.3  State and Federal Regulations

1.3.1 Lighting

WARNING

If any lighting is installed or 
changed, it must not alter or 
prevent vehicle compliance with 

any existing State or Federal standards such as 
FMVSS 108 – Lamps, Reflective Devices, and 
Associated Equipment. 

1.3.2  Rear Impact Guards

WARNING

When stored in the transport 
position, this liftgate must 
provide protection against rear 

impact and comply with State and Federal standards 
in your area. Anthony Liftgates offers a bolt-on 
bumper, which meets the requirements of this 
standard. 

1.4  If Maintenance Help is Required

1.4.1 Maintenance (Dealer)

For additional information on installation, refer to the ETU 
TuckUnder™ liftgate website 

www.anthonyliftgates.com.

 

7R¿QGWKHPRVWFXUUHQWYHUVLRQRIWKHUHIHUHQFHPDWHULDO

choose LIFTGATES, TUCKUNDER™, ETU, and then 
DOWNLOADS.

If you have any doubts or questions about installation, 
call us. Before doing so, have the serial number, model 
number, and lift capacity of your liftgate available.

Anthony Liftgates, Inc.  
1037 West Howard Street 

 

Pontiac, Illinois 61764   
(815) 842-3383 or 800-482-0003

1.4.2  Customer Service and Parts (End User)

For service or ordering replacement parts, contact an 
authorized dealer by going to 

www.anthonyliftgates.com

 

and selecting the FIND A DEALER tab. Enter your zip 

FRGHWR¿QGWKHQHDUHVWDXWKRUL]HGVHUYLFHORFDWLRQ

 

SAFETY

 INSTRUCTIONS

N ING

AR

Being unaware of safety 
recommendations can 
lead to personal injury. 

The user must make sure all decals are attached to 
the liftgate and truck and are legible.

Summary of Contents for ETU-20-44





















Reviews: