background image

Anthony Lifgtates, Inc. 

 

L-501 Models

www.anthonyliftgates.com  

800-482-0003

DANGER

To prevent serious bodily injury, 
keep sparks, lighted matches, 
and open flames away from the 

top of the battery, because battery gas can explode.  
Always follow all the manufacturers’ safety 
recommendations when working around the truck’s 
battery.

Take precautions to avoid sparks coming into 
contact with the truck’s fuel tank, brake lines, 
or other flammable components.  Sparks can 

cause an explosion of combustible materials, resulting 
in serious injury or death. 

Never secure the power cable to anything 
which allows it to contact sharp edges, other 
wiring, the fuel tank, fuel lines, brake lines, air 

lines, exhaust system, or any other object that could 
cause the power cable to wear or be damaged.  A cut 
battery cable can cause sparks resulting in loss of 
vehicle control, serious injury, or even death.

WARNING

If required for installation, always 
use a cutting torch in a well 
ventilated area and, if in an 

enclosed area, vent the fumes to the outside.  Breathing 
the smoke and fumes can cause serious injury. 

Always follow all State and Federal health and 
safety laws and/or local regulations when using 
a cutting torch.  Also, follow all manufacturer’s 

safety guidelines.  If other people are present during 
the installation of the liftgate, make sure they remain 
clear of the cutting area.  

To avoid eye injury, always wear eye protection 
with the proper lens to protect your eyes.

Failure to prevent the truck from moving during 
the installation of the liftgate could result in a 
serious crushing injury.

Do not work under the liftgate while it is 
suspended from the lifting equipment.  Failure 
of the lifting equipment could cause serious 

crushing injuries.  Do not remove the lifting equipment 
until the liftgate is completely bolted onto the truck 
frame.

To prevent personal injury, clean up any 
spilled fluids immediately. To avoid 
tripping, do not leave tools or 

components laying around in the work area.

CAUTION

Anthony Liftgates recommends not riding the 
liftgate, however, if the delivery operation 
requires it, make sure your footing is stable 

before raising or lowering platform.  Always stand 
away from the edge.  When on the ground, always 
stand clear of liftgate when it is operating.

Always use/set the truck’s parking brake before 
operating the liftgate.  Failure to follow this 
recommendation can result in injury.

Do not place hands or feet in pinch points.  

Do not place your feet under the liftgate. 

SAFETY
INSTRUCTIONS

To prevent injury, the liftgate and its related 
components should only be installed by a 
qualified installer.  They should have knowledge 

and skill in using lifting equipment and a cutting 
torch.

N ING

AR

To prevent possible injuries due to improper 
operation, make sure all decals are attached to 
the liftgate and/or truck and are legible at all 

times.

Summary of Contents for ALB-1500





















































Reviews: