background image

5

6. Rear Right Speaker Out Pin: Connect the RET-R connector to this pin.
7. Rear Left Speaker Out Pin: Connect RET-L connector to this pin.

3.5" DEVICE INSTALLATION

With the front bezel facing you, swing the front door out. You can see there are three 5.25" and
two 3.5" external drive bays. Inside the case there are four 3.5" drive cages.

1. On the sides of the front bezel there are two tabs. Press the tabs to remove the top half

of the bezel.

2. Unscrew the two thumbscrews located on the drive bay assembly and slide it out.
3. Install your floppy drive into the bottom drive bay. Mount another 3.5" device into the top 

drive bay if applicable.

4. Slide the whole assembly back into the case and fasten it with the thumbscrews.

Inside the case, there is a 3.5" drive cage. It can hold three 3.5" devices.

5. Pull the quick release lever towards the rear of the case to release the cage. Put the cage

on a flat surface.

Note:

If you want to have a cooling fan in the drive cage, you should

install the fan before installing the drives.

6. Mount your other 3.5" devices into the drive cage.
7. Slide and lock the drive cage back into the case.
8. Find a small 4-pin connector on the power supply and connect it to the male 4-pin connector

on the floppy drive.

9. Connect a large 4-pin connector from the power supply to the male 4-pin connector on

each of the other devices.

5.25" DEVICE INSTALLATION

1. There are metal plates covering the 5.25" drive bays.
2. Carefully twist the metal plate back and forth until it breaks off.

Note:

Don't break off plates covering drive bays that you are not going to use. Be careful 

of the newly exposed metal where the plates were attached as these areas are likely to be sharp.

3. Take two drive rails and mount them to the sides of the 5.25" device.

Make sure the metal portion is angled away from the device and facing forward.

4. Slide the device into the drive bay until you hear a click.
5. Mount the other devices accordingly.
6. Connect a large 4-pin  connector from the power supply to the male 4-pin connector on 

each of the devices. After you have finished the installation, carefully use your thumbs to 
push the plastic drive bay covers off the bezel and attach the bezel back into the case. Like 
the metal plates, take off only the covers for the drive bays you are using now.

COOLING SYSTEM 
The TriCool fan

The case includes one 120mm TriCool fan installed in the rear. This fan has a three-speed switch
that lets you choose between quiet, performance, or maximum cooling.
(See specifications below.) The fan is installed so that the air is blowing out of the case. Connect
a large 4-pin connector from the power supply to the male 4-pin connector on the fan.

Note:

The minimum voltage to start the fan is 5V. We recommend our users to set the fan speed

to High if you choose to connect the fan to a fan control device or to the Fan-Only connector
found on some Antec power supplies. A fan-controlled-device regulates the fan speed by varying the
voltage to it. The voltage may start as low as 4.5 V to 5V. Connecting a TriCool set on Medium or
Low to a fan-control device may result in the fan not being able to start. The already lowered volt-
age from the fan control device will be further reduced by the TriCool circuitry below 5V.

Summary of Contents for Performance TX635









Reviews: