3
♦
If the supply cord is damaged, it must be replaced by manufacturer or its service agent or similarly qualified
personnel in order to avoid a hazard.
♦
The output nozzle becomes very hot during operation (300°C). Keep flammable materials at least 50 cm
away from the nozzle.
♦
Always allow your ANTARI Fog Machine to cool down before attempting to clean or service it.
Danger of Explosion
♦
Never add flammable liquids of any kind (such as oil, gas, perfume) to the fog liquid.
♦
Use only high-quality, water-based fog liquid that your dealer recommends. Other fog liquids may cause
clogging or “spitting”.
♦
Always make sure there is sufficient liquid in the tank. Operating this unit without liquid will cause damage
to the pump as well as over-heating of the heater.
♦
If your ANTARI Z-1200II Fog Machine fails to work properly, discontinue use immediately. Drain all fog
liquid from the tank, pack the unit securely (preferably in the original packing material), and return it to your
ANTARI dealer for service.
♦
Always drain tank before mailing or transporting this unit.
♦
Never drink fog liquid. If it is ingested, call a doctor immediately. If fog liquid comes in contact with skin or
eyes, rinse thoroughly with water.
Note:
Pay attention to all warning labels and instructions printed on the exterior of your ANTARI Fog Machine
Unpacking & Inspection
Open the shipping carton and verify that all equipment necessary to operate the system has arrived intact. The
shipping carton should contain the following items:
1. One unit of Z-1200II Fog Machine
2. Power
cord
3. Z-8 multi-function remote control with attached cord
4. User
Manual
If any equipment is missing contact your ANTARI dealer immediately.
Before beginning your initial setup on ANTARI Z-1200II Fog Machine, make sure that there is no evident
damage caused by transportation. In the event that the unit’s housing or cable is damaged, do not plug it in
and do not attempt to use it until after contacting your ANTARI dealer for assistance.
Setup
♦
Remove all packing materials from shipping box. Check that all foam and plastic padding is removed,
especially in the nozzle area.
♦
Place fog machine on a flat surface and remove fog liquid tank cap.
♦
Fill with ANTARI fog liquid or other high-quality water-based fog fluid recommended by ANTARI dealer.
Any other types of fluid can damage the unit resulting in spitting and serious clogging problem. When filled,
place cap back on liquid tank. Be careful not to exceed the maximum fluid level. DO NOT OVERFILL.
♦
Firmly attach the Z-8 remote control cable to the proper input on the back of the machine.
Operation
♦
Add fluid carefully to the liquid tank. Do not overfill the tank.
♦
Plug the remote control cord into the slot marked remote control on the back of the machine.
♦
Plug power cord into a grounded electrical outlet. Turn the power switch to “
ON
” on the back of the
machine. The red light on the remote will turn ON once the machine is plugged into a power outlet and the
ON/OFF switch is turn ON. The unit will take a couple of minutes to warm up the heater. During this time
the machine cannot generate fog. The green light on the remote will turn ON once the machine is ready to
produce fog.
♦
To emit fog press the green button on the remote. Z-1200II is controlled via the Z-8 remote control.
4
♦
For detailed instruction on the various functions on operating your Z-1200II Fog Machine, see the section
titled “
Remote Control Operation
”.
Important:
Always monitor tank fluid level as you are fogging. Running a fog machine with no fluid can
permanently damage the unit.
If your model includes a mounting bracket designed for overhead installation, it may be installed
floor level or suspended overhead. If the unit is to be mounted using the bracket, it is important
that the fog does not shoot directly at any one’s face. Whatever installation method you choose,
do not allow the unit to have more than a 15 degree angle or onclination.
Note:
A fluid level sensor is installed on the unit. The machine will stop to fog if the fluid is lower than the
maximum level.
If you experience low output, pump noise or no output at all, unplug immediately. Check fluid level, the
external fuse, remote control connection and power from the wall. If all of the above appears to be O.K.,
plug the unit again. If fog does not come out after holding the remote button down for 30 seconds, check
the hose attached to the tank to make sure there is fluid going through the hose. If you are unable to
determine the cause of the problem, do not simply continue pushing the remote button, as this may
damage the unit. Return the machine to your ANTARI dealer.
Specification
Model Number
Z-1200II
Power Supply
AC100-120V, AC220-240V / 50HZ-60HZ
Power Consumption
1250 W
Output Volume
ca. 500 m³/min.
Tank Capacity
2.5 Liter
Fluid Consumption
44 min./Liter
Weight
10.9 Kg.
Dimensions(mm)
L458 W243 H177
Remote Included
Z-8
Remote Control Operation
♦
Z-8:
10 meter wired multi-function remote control with 5-PIN plug for ANTARI Fog Machine model
Z
-1200II.
The
Interval
knob adjusts the time between discharges when the timer function is engaged. The range is
from 10 seconds to 250 seconds.
The
Volume
knob controls the volume of the fog produced. The range is from 0% - 100% of maximum
output.
The yellow
TIMER
button controls the timer function. Depress the button to activate. When activated, the
yellow light will turn ON. Adjusting the interval knob will determine the time between fog output (10 – 250
seconds). The duration of output is set at 15 seconds. The volume can be adjusted using the volume knob
to control the amount of fog produced.
The red
CONTINUOUS
button sets the
machine to constant fog production. To activate this function,
depress the red button. The volume knob can be used to regulate the volume of the steady stream of fog
produced.
The green
MANUAL
button will produce a continuous blast at maximum volume while the button is held
down. When released, the manual function stops and the machine will return to the previous setting; timer,
continuous, or stationary.
Note:
The continuous function will override the Timer function. Therefore, if both buttons have been
depressed the Z-1200II will fog continuously. The manual function overrides all functions. When
depressed and held down the Z-1200II will fog at maximum volume for as long as the button is held
down, regardless of the machine’s setting at the time.
Performance Note
