4
If your model includes a mounting bracket designed for overhead installation, it may be installed
at floor level or suspended overhead. If the unit is to be mounted using the bracket, it is
important that the fog does not shoot directly at any one’s face. Whatever installation method
you choose, do not allow the unit to have more than a 15 degree angle of inclination.
Note:
A fluid level sensor is installed on the unit. The machine will stop to fog if the fluid is lower than usable
level.
If you experience low output, pump noise or no output at all, unplug immediately. Check fluid level, the
external fuse, remote control connection and power from the wall. If all of the above appears to be O.K.,
plug the unit again. If fog does not come out after holding the remote button down for 30 seconds, check
the hose attached to the tank to make sure there is fluid going through the hose. If you are unable to
determine the cause of the problem, do not simply continue pushing the remote button, as this may
damage the unit. Return the machine to your ANTARI dealer.
Specification
Model Number
Z-800II
Z-1000II
Z-1020
Power Supply
AC100-120V, AC 220-240V / 50HZ - 60HZ
Power Consumption
800W
1,000W
1,000W
Output Volume
85 m
³
/min.
284 m
³
/min.
284 m
³
/min.
Tank Capacity
0.8 Liter
1.7 Liter
2.5 Liter
Fluid Consumption
37 Min./ 0.8 Liter
49 Min./ Liter
24 Min./ Liter
Weight
3.5 Kg.
6.6 Kg.
9.7 Kg.
Dimensions(mm)
L315 W128 H166
L430 W198 H153
L370 W295 H135
Remote Included
Z-10
Z-10
Z-10
Optional Remote
Z-40, Z-50
Z-40, Z-50
Z-40, Z-50
Remote Control Operation
♦
Z-10:
10 meter wired remote controller with five-prong plug of ANTARI Fog Machine models
Z
-800II,
Z-1000II and Z-1020. The red lamp indicates that the unit is receiving power. When the fog machine has
reached operating temperature the green lamp on this remote control will light up, indicating that the
operator may begin fog emission by pressing the red button. The green lamp turns OFF during fog
machine warm-up (approx. 4 minutes) amd re-heating cycles (approx. 1-2 minutes), and turns ON when
the machine becomes operational.
♦
Z-40:
10 meter wired remote controller with five-prong plug for ANTARI Fog Machine models Z-800II, Z-
1000II and Z-1020. Its two knobs allow the operator to customize fog machine functions by adjusting output
duration and interval. Press the yellow TIMERS button to activate the timer function. Adjust the interval
between each fog emission (within the range of 10 seconds to 5 minutes) by means of the INTERVAL
control knob. Adjust the duration of each fog emission (within the range of 1 to 10 seconds) by means of
the DURATION control knob. When pressed, the green MANUAL button overrides all other functions
controls, and activates maximum output. Press the red CONTINUOUS button for continuous output.
♦
Z-50:
Wireless remote controller with five-prong plug for ANTARI Fog Machine models Z-800II, Z-1000II
and Z-1020. A remote operation is possible up to a distance of 50 meters.
Performance Note
♦
All fog machines develop condensation around the output nozzle. Because this may result in some
moisture accumulation on the surface below the output nozzle, consider this condensation when installing
your unit.
♦
All fog machines may sputter small amounts of fog occasionally during operation and for a minute or so
after being turned off.
♦
All fog machines have a recycling period after long bursts when the machine will shut itself down for a short
period in order to heat up again. During this time no fog can be produced.
Maintenance
