Antares 90944 User'S Manual And Installation Instructions Download Page 2

Page: 2 / 21

ASC+ System Auto Split Charge & Engine Start Protect

User Guide and Installation Instructions

Document No 13362 Issue 04

Page 2 of 21

Table of Contents

IMPORTANT SAFETY INFORMATION

Type Approval – Information

Error! Bookmark not defined.

System overview

Equipment description

Controller module

User switch panel

Control cables

Contactor type & rating

Power cables

Installation 7

Choosing a location

Control module installation

Contactor installation

Switch installation

Safety Notices

Error! Bookmark not defined.

Installation sequence

Testing the assembly

System operation

ESP (Engine Start Protect) operation

Manual de-isolation (turn system on)

Manual isolation (turn system off)

Low battery (ESP) protection

Battery isolated, and “sleep mode” power consumption

ASC (Auto Split Charge) operation

Using Battery Link (Emergency / Assured Start) function

ASC standard operation

ASC dual sense operation

ASC battery protect

ASC overvoltage protection

Fault finding and flow charts

ESP (Engine Start Protect) options

Spares 20

Summary of Contents for 90944






















Search results

Summary of Contents for 90944

Reviews:

Related manuals for 90944

Brands by name

Popular brands

Antares 90944, User'S Manual And Installation Instructions

Search results

Summary of Contents for 90944

Reviews:

Related manuals for 90944

Brands by name

Popular brands