Antares 90944 User'S Manual And Installation Instructions Download Page 20

Page: 20 / 21

ASC+ System Auto Split Charge & Engine Start Protect

User Guide and Installation Instructions

Document No 13362 Issue 04

Page 20 of 21

Battery low disconnect voltage

Single ABP: 10.5
or 21 volts.
Dual ABP: 10.5 &
12.2 volts, or 21 &
24.4 volts.

May be set in the range 10 to
12.25 volts or 20 to 24.5 volts

ASC settings:

Parameter

Default

Alternative settings

Dual voltage sense

Enabled

Main sense only
or
Aux sense only

Ignition off forces ASC off

Disabled

Enabled

Battery sensing (battery present
or absent)

Enabled Disabled

Assured start activation

External switch

Crank signal input
or
Automatic detection

Switching hysteresis

Standard

May be set in the range 0.1 to
2.0 volts

Spares

12V System spares

Antares Part No

Description

Type / Value

80244 Contactor

12V,

125A

Latching

80298 Contactor

12V,

250A

Latching

81333

Switch Kit

12V, 2 x Switches ASC + ESP

56178 LED

12V

Green

82524

Contactor Loom

4 way, 5M, Connector to free end

82516

Switch Assembly Loom 6 way, 5M, Connector to free end

See note 1 below Controller

12V, 2 x contactor

Summary of Contents for 90944






















Search results

Summary of Contents for 90944

Reviews:

Related manuals for 90944

Brands by name

Popular brands

Antares 90944, User'S Manual And Installation Instructions

Search results

Summary of Contents for 90944

Reviews:

Related manuals for 90944

Brands by name

Popular brands