ANTAIRA LNX-800A-E Series Hardware Manual Download | Manualshive

Page: 5 / 22

background image

Antaira Technologies - Industrial Ethernet Switches
LNX-800A-E Series - Hardware Manual - v1.0

Table of Contents

1.1 Product Hardware Features

1.2 Package Contents

1.3 Safety Precaution

2 Hardware Description

2.1 Physical Dimensions

2.2 Front View Panel

2.3 Top View Panel

2.4 LED Indicators

2.5 Ethernet Ports

2.8 Wiring the Power Inputs

2.9 Wiring the Fault Alarm Contact

2.10 Grounding Note

3 Mounting Installation

3.1 DIN-Rail Mounting

3.2 Wall Mounting

4 Hardware Installation

4.1 Installation Steps

4.2 Maintenance and Service

4.3 Troubleshooting

5 Technical Speciﬁcations

«
...
3
4
5
6
7
...
»

Summary of Contents for LNX-800A-E Series























Reviews:

No comments

Related manuals for LNX-800A-E Series

D-PFS4226-24ET-240

Brand: Dahua Pages: 58

Brand: Tripp Lite Pages: 80

Brand: Grizzly Pages: 2

Brand: Woxcon Pages: 42

Brand: Lindy Pages: 5

Brand: Microsonic Pages: 2

Brand: Labgear Pages: 8

Brand: Omega Pages: 17

Brand: QSFPTEK Pages: 8

Brand: LEGRAND Pages: 197

Brand: Valcom Pages: 1

stiro RWS-211D/N

Brand: Zamel Pages: 11

Brand: Foxtel Pages: 9

Brand: ENSIM SENSORS Pages: 15

Brand: Southern States Pages: 32

Brand: Shinybow USA Pages: 32

Brand: Kramer Pages: 12

Brand: Knightsbridge Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands