background image

Antaira Technologies - Industrial Ethernet Switches
LNX-800A-E Series - Hardware Manual - v1.0

2.3 Top View Panel

Figure 2.3, below, shows the top panel of the product series:

Figure 2.3 - Top View Panel

2.4 LED Indicators

There are LED light indicators located on the front panel of the industrial Ethernet switch that display the power status and

network status. Each LED indicator has a different color and has its own specific meaning, see below in Table 2.1.

LED

Color

Description

P1

Green

On

Power Input 1 is active

Off

Power Input 1 is inactive

P2

Green

On

Power Input 2 is active

Off

Power Input 2 is inactive

Fault

Red

On

Power Input 1 or 2 is inactive

Off

Both power input 1 and 2 are active

LAN Port 1~8

Green

On

Connected to network, 10/100Mbps

Flashing

Networking is active

Off

Not connected to network

Green

On

Ethernet port full-duplex

Flashing

Collision of packets occurs

Off

Ethernet port half duplex or not connected to network

Table 2.1 - LED Indicators

Note: “P1” is the abbreviation for “Power 1”, “P2” is for “Power 2”, “LNK” is for “Link”, and “ACT” is for “Activity”.

5

Summary of Contents for LNX-800A-E Series























Reviews: