ANTAIRA APX-110N5 User Manual Download Page 64

Page: 64 / 68

NTP Client, Web, Telnet, SSH Server

NTP Client:

The Network Time Protocol (NTP) is a protocol for synchronizing the clocks

of computer systems over packet-switched, variable-latency data networks. It can be used

to set the device system time. System Time is reported next to the every System Log entry

while registering system events if Log option is enabled.

Web Server:

the following the device Web Server parameters can be set there:

Use Secure Connection (HTTPS):

If checked Web server will use secure HTTPS mode.

HTTP mode is selected by default.

Secure Server Port:

Web Server TCP/IP port setting while using HTTPS mode.

Server Port:

Web Server TCP/IP port setting while using HTTP mode.

Telnet Server:

the following the device Telnet Server parameters can be set there:

Enable Telnet Server:

Enables Telnet access to the device.

Server Port:

Telnet service TCP/IP port setting.

SSH Server:

the following the device SSH Server parameters can be set there:

Enable SSH Server:

Enables SSH access to the device.

Server Port:

SSH service TCP/IP port setting.

System Log

Enable Log:

option enables the registration routine of the system log messages.

Enable Remote Log enables the syslog remote sending function while System log

messages are sent to a remote server specified by the Remote Log IP Address and

Remote Log Port.

Remote Log IP Address

is the host IP address where syslog messages should be sent.

Remote host should be configured properly to receive syslog protocol messages.

Remote Log Port

is the TCP/IP port of the host syslog messages should be sent. "514" is

the default port for the commonly used system message logging utilities

Every logged message contains at least a

System Time

and a Host Name.

Usually a particular service name which generates the system event is
specifies also within the message. Messages from different services have
different context and different level of the details. Usually

error

warning

informational

system services messages are reported. The more detailed

system messages are reported, the greater volume of log messages will be
generated.

uConfig Utility

The exclusive uConfig utility allows users to access the user-friendly Web configuration

interface of the access point without having to change the TCP/IP setup of the

workstation.

Summary of Contents for APX-110N5





































































Search results

Summary of Contents for APX-110N5

Reviews:

Related manuals for APX-110N5

Brands by name

Popular brands

ANTAIRA APX-110N5, User Manual

Search results

Summary of Contents for APX-110N5

Reviews:

Related manuals for APX-110N5

Brands by name

Popular brands