ANTAIRA APX-110N5 User Manual Download Page 51

Page: 51 / 68

LAN Setting

LAN MAC:

displays the MAC address of the device LAN (Ethernet) interface.

LAN Mode:

displays the mode used, either static or DHCP client.

LAN IP Address:

displays the current IP address of the LAN (Ethernet) interface.

LAN Gateway IP Address:

displays the IP address of the gateway used in LAN.

LAN Primary DNS IP:

displays the Primary DNS IP address of the LAN setting.

LAN Secondary DNS IP:

displays the Secondary DNS IP address of the LAN setting.

WAN Setting

WAN MAC:

displays the MAC address of the device WAN interface.

WAN Mode:

displays the mode used, either DHCP, PPPoE or Static IP.

WAN IP Address:

displays the current IP address of the WAN interface.

WAN Gateway IP Address:

displays the IP address of the gateway used in WAN.

WAN Primary DNS IP:

displays the Primary DNS IP address of the WAN setting.

WAN Secondary DNS IP:

displays the Secondary DNS IP address of the WAN

setting.

Radio

Wireless Mode:

displays the current operating mode of the device.

Local AP SSID:

displays the current SSID (Service Set Identifier) of device when

operates in access point mode.

Frequency:

displays current operating frequency running in device.

WLAN MAC:

displays the MAC address or BSSID of the current active WLAN card

running in device.

WLAN Local/Remote AP MAC:

displays the MAC address of the WLAN card

connected to it.

WLAN Security

display the current active security mode.

Summary of Contents for APX-110N5





































































Search results

Summary of Contents for APX-110N5

Reviews:

Related manuals for APX-110N5

Brands by name

Popular brands

ANTAIRA APX-110N5, User Manual

Search results

Summary of Contents for APX-110N5

Reviews:

Related manuals for APX-110N5

Brands by name

Popular brands