background image

N

3

N

•  Use this appliance ONLY for its intended use as 

described in this manual.

15. The Sensor Pad is not intended to be used to 
determine if a child is out of the cot.
16. ALWAYS be sure to immediately check on 
baby whenever an alarm sounds.
17. Keep cords out of the reach of ANY children.
18. ONLY use the chargers and power adaptors 
provided. Do not use other types as this 
may damage the device and battery pack (if 
included in your model).
19. Adult assembly required. Keep small parts 
away from children when assembling.
20. Follow instructions and test this monitor and 
its functions so you are familiar with it prior to 
actual use. ALWAYS

 be sure that both the transmitter 

and receiver are working properly and are within range 
of each other – check periodically and when changing 
location of the Nursery Unit.

21. DO NOT touch the plug contacts especially 
with sharp or metal objects.
22. DO NOT use the baby monitor near water.

 

Care should be taken so that objects DO NOT fall onto 
units and that liquids are not spilled into either unit or 
Sensor Pad through its openings. 

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

DO NOT EXPOSE TO RAIN OR MOISTURE

23. Keep monitor AWAY from heat sources (such 
as stoves, radiators, etc.).

 Heat can damage the 

case or electrical parts.

24. ALWAYS place both the Nursery Unit and the 
Parent Unit on a flat solid surface in an upright 
position that allows for proper VENTILATION.

 DO 

NOT place on sofas, cushions, beds, etc. which may 
block ventilation or anywhere that would muffle the 
sound or interfere with the normal flow of air.

25. The baby monitor can only be used between 
10°C and 40°C (50°F and 104°F), max 75% RH. Do 
not exceed 28°C (82,4°F) for long periods of use.

WARNINGS AND SAFETY 
INSTRUCTIONS - BATTERY SPECIFIC

 

WARNING

Do not ingest the battery, Chemical Burn Hazard. 
This product contains a coin/button cell battery. If the 
coin/button cell battery is swallowed, it can cause severe 
internal burns in just 2 hours and can lead to death. 
Keep new and used batteries away from children. If the 
battery compartment does not close securely, stop using 
the product and keep it away from children. If you think 
batteries might have been swallowed or placed inside any 
part of the body, seek immediate medical attention.

26. The Parent Unit battery is a replaceable 
Li-Ion battery. The Wireless Sensor Pad 
uses a replaceable Coin/Button Cell Lithium 

Battery. Only use the Angelcare recommended 
replacement battery (see Technical 
Specification).

 

•  Danger of explosion if the wrong battery is used or if 

replaced incorrectly. Refer to User’s Guide for correct 
battery installation. 

•  DO NOT short circuit supply terminals.

27. DO NOT mix old and new batteries and only 
use Angelcare recommended replacement 
batteries

 (see Technical Specification).

28. The Coin/Button Cell Battery represents a 
small part and a choking hazard – KEEP away 
from children!
29. Exercise care in handling batteries in order 
not to short out the batteries

 with conducting 

materials such as rings, bracelets and keys. 

30. Overcharging, short circuiting, reverse 
charging, mutilation, or incineration of 
batteries must be avoided

 to prevent one or more 

of the following occurrences: release of toxic materials, 
release of hydrogen and/or oxygen, gas and rise in 
surface temperature.

31. DO NOT attempt to recharge batteries 
provided with or identified for use with this 
product that are not intended to be charged.

 

The batteries may leak corrosive electrolyte or explode.

32. Incorrect polarity installation of the 
batteries in the end product must be avoided.

 

Reverse insertion of batteries can cause charging, and 
that may result in leakage or explosion.

33. 

Battery swelling can occur with the type of battery 

used in the Parent Unit if not used or stored correctly 
including but not limited to the age, usage pattern, 
environmental conditions (over heating), over-charging, 
over-discharging, using incorrect chargers and physical 
abuse/damage. Refer to Angelcare online Battery 
Warning Statement: 

https://angelcarebaby.com/battery-safety
34. Remove batteries from units if you store the 
product over 30 days

 because the batteries could 

leak and damage the product. 

35. 

Discard ‘dead’ batteries as soon as possible since 

‘dead’ batteries are more likely to leak in a product. 
If a battery has leaked or vented, discard product 
responsibly. 

36. DO NOT store this product, or the batteries 
provided with or identified for use with this 
product, in high-temperature & high humidity 
environments and avoid direct sunlight – this 
could lead to potential battery leakage, swelling 
and potential harm and damage. The parent 
Unit Lithium battery should be stored at 23±5°C 
(73.4 ± 9°F) at ≤ 75% RH. Always store the 
product with approximately 50% charge and 
do not store for more than 3 months without 
charging.
37. CAUTION

•  Danger of explosion if battery is incorrectly re placed. 

Replace only with the same or equivalent type.

•  Battery cannot be subjected to high or low extreme 

temperatures, low air pressure at high altitude during 
use, storage or transportation.

3

Summary of Contents for AC327

















Reviews: