Angelcare AC017 Owner'S Manual Download Page 26

1. THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT SUPERVISION. This product 

is designed to aid in the monitoring of your child. When using the monitor, you 

must still provide the supervision necessary for the continued safety of your 

child. Monitoring of premature babies, or those considered to be at risk, should 

always be carried out under the supervision of a health professional. This monitor 

SHOULD NOT be used as a medical device, nor as a device to prevent Sudden Infant 

Death Syndrome (SIDS).
2. ALWAYS be sure to immediately check on baby whenever an alarm sounds. 
3. DO NOT use monitor near water (such as bath tub, sink, etc.). 

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

DO NOT EXPOSE TO RAIN OR MOISTURE

4. Keep monitor AWAY from heat sources (such as stoves, radiators, etc.). 
5. ALWAYS place the Nursery Unit on a flat surface in an upright position and 

allow for proper ventilation. DO NOT place on sofas, cushions, beds, etc. which 

may block ventilation.
6. This product is NOT a toy. DO NOT allow children to play with it. 
7. This product contains small parts. Adult assembly required. Exercise care when 

unpacking and assembling the product and keep small parts away from children.
8. When using the monitor, the room temperature should be between 50°F and 

104°F (10 °C and 40 °C).

 BATTERY WARNING

9. The Wireless Sensor Pad battery is a replaceable Button Cell Lithium battery. 

Only use the Angelcare

® 

e recommended replacement battery. Danger of explosion 

if the wrong battery is used or if replaced incorrectly. Refer to your user manual 

for correct battery installation. DO NOT short circuit supply terminals. Remove the 

batteries from your Nursery Unit and Sensor Pad if product is to be stored for an 

extended period of time. Dispose of batteries according to your local ordinances. 

The Button cell battery represents a small part and a choking hazard. ALWAYS keep 

all batteries away from children.
10. IMPORTANT SAFETY INSTRUCTIONS
10.1 
Heed all warnings – All warnings on the product and in the operating 

instructions should be adhered to.
10.2 Follow all instructions – All operating and use instructions should be followed.
10.3 Water and moisture - DO NOT use this apparatus near water. For example, 

near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet environment or near 

a swimming pool and the like. Care should be taken so that objects DO NOT fall 

onto units and that liquids are not spilled into either unit or Sensor Pad through 

its openings.
10.4 Cleaning - Disconnect all units before cleaning. DO NOT immerse in water 

any part of the monitor. Clean only with dry cloth. 
10.5 Ventilation - DO NOT block any ventilation openings. Allow for proper 

ventilation when units are in use. DO NOT cover the Nursery Unit with any object 

such as a blanket. DO NOT place it in a drawer or in any location which would muffle 

the sound or interfere with the normal flow of air.
10.6 Heat sources - DO NOT install near any heat sources such as radiators, heat 

registers, stoves, TVs or other apparatus (including amplifiers) that produce heat. 

Heat can damage the case or electrical parts.
10.7 Accessories - Only use attachments/accessories specified by the 

manufacturer. DO NOT place this product on an unstable cart, stand, tripod, 

bracket or table. The product may fall, causing serious injury to a child or adult 

and serious damage to the product. Use ONLY with a cart, stand, tripod, bracket or 

table recommended by the manufacturer or sold with the product. Any mounting 

of the product should follow the manufacturer’s instructions.

10.8 Servicing - DO NOT attempt to service this product yourself as opening or 

removing covers (except battery door) may expose you to dangerous voltage 

or other hazards.
10.9 Replacement parts - When replacement parts are required, be sure the 

replacement parts specified by the manufacturer have the same characteristic 

as the original part. Unauthorized substitution may result in fire, electric shock 

or other hazards.
10.10 Usage - This baby monitor is intended as an aid. It is NOT a substitute for 

responsible and proper adult supervision and should not be used as such. Use this 

appliance ONLY for its intended use as described in this manual.
10.11 Object and Liquid Entry - NEVER push objects of any kind into this product 

through casing slots as they may touch dangerous voltage points or short out 

parts that could result in a risk of fire or electric shock. NEVER spill liquid of 

any kind on the product.
10.12 Vibration Source - When the monitor is in use, DO NOT use a cot mobile or 

other cot accessories that may produce vibrations. Other sources of vibrations 

may include fans, washing machines, loud music, etc. These sources of vibration 

may interfere with the performance of your Angelcare

®

 monitor and the alarm will 

not sound if it continues to detect any movement other than your baby’s. Be sure 

all vibration sources are eliminated before using the monitor.
10.13 You may experience false alarms for several reasons. The most common reason 

is the Nursery Unit has not been turned OFF after you have removed your baby from the 

cot. Another reason is the Sensor Pad has not been placed under the mattress properly.  

Be sure the Sensor Pad is on a flat, firm surface with the Angelcare

®

 logo side facing 

up. The sensitivity level may also need to be adjusted. Refer to Step 4.3. Always 

be sure to immediately check on baby whenever an alarm sounds.
10.14 Sensor Pad - Your Sensor Pad can be used in any cot that is stationary. 

If the cot has a spring or slat base, place a hard board between the cot base 

and the Sensor Pad measuring at least 13’’ x 13’’ (33 x 33 cm) and 1/4’’ (6 mm) 

thick. Only use your Angelcare

®

 monitor in a stationary sleeping environment 

such as a cot where the Sensor Pad can rest on a completely flat, firm surface.  

The Sensor Pad is made of plastic and does not permit the air to circulate. 

Therefore, mildew build up could develop underneath the mattress in the Sensor 

Pad area. We suggest rotating the mattress regularly to prevent any mildew. 

11. IMPORTANT SAFETY INSTRUCTIONS RELATED TO USE OF BATTERIES
11.1 
Use ONLY the type and size of battery specified in the owner’s manual. There 

is a risk of explosion if battery is replaced with an incorrect type.
11.2 DO NOT use rechargeable batteries in the Nursery Unit. Use alkaline batteries 

ONLY.
11.3 DO NOT dispose batteries in fire. They may explode. Check with local 

regulations for possible special disposal instructions.
11.4 Exercise care in handling batteries in order not to short out the batteries 

with conducting materials such as rings, bracelets and keys. Overcharging, short 

circuiting, reverse charging, mutilation, or incineration of batteries must be 

avoided to prevent one or more of the following occurrences: release of toxic 

materials, release of hydrogen and/or oxygen, gas and rise in surface temperature.
11.5 DO NOT attempt to rejuvenate the battery provided with or identified for use 

with this product by heating them. Sudden release of battery electrolyte may 

occur, causing burns or irritation to eyes or skin.
11.6 If and when necessary, the battery must be replaced with identical new ones 

or equivalent (volts and size).
11.7 Reverse polarity installation of the batteries in the end product must be 

avoided. Reverse insertion of batteries can cause charging, and that may result 

in leakage or explosion.
11.8 Remove the battery from this product if you store the product over 30 days 

because the battery could leak and damage the product.
11.9 Discard ‘dead’ batteries as soon as possible since ‘dead’ batteries are more 

likely to leak in a product. If a battery has leaked or vented, it should be replaced 

immediately using protective gloves.
11.10 DO NOT store this product, or the battery provided with or identified for use 

with this product, in high-temperature areas.

OWNER’S MANUAL

 

KEEP YOUR OWNER’S MANUAL FOR FUTURE REFERENCE.
PLEASE READ THE WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING & 

USING THE PRODUCT.
FAILURE TO FOLLOW THE WARNINGS AND THE INSTRUCTIONS COULD RESULT IN SERIOUS 

INJURY OR DEATH OR DAMAGES TO THE PRODUCT.
THE SENSOR PAD FEATURE IS NOT FOR USE WITH ADULTS, CHILDREN OR INFANTS OLDER 

THAN 24 MONTHS.
THE SENSOR PAD IS NOT INTENDED TO BE USED TO DETERMINE IF A CHILD IS OUT OF 

THE COT.

 WARNING

Adult assembly required.

Keep small parts away from children when assembling.
We, at Angelcare

®

, stand behind all of our products.

If you are not completely satisfied or have any questions,

United States and Canada: Please contact us at: angelcare@

cdecinc.ca

Other countries: Please contact your local distributor: 

international.angelcarebaby.com

 

WARNINGS

  

WARNING ‑

 KEEP the Nursery Unit out of the reach of children more than 3 feet or  1 metre away. 

• This product is NOT a Toy. NEVER allow children to play with it.

26

256AC_01_Manuel_AC017_Pabobo_m2.indd   26

2018-05-30   10:30 AM

Summary of Contents for AC017













































Reviews: