background image

Template  version:1 

4/17 

7.  Consult your physician if you have any doubt about below cases: 

1) The application of the cuff over a wound or inflammation diseases; 

2) The application of the cuff on any limb where intravascular access or therapy, or an 

arterio-venous (A-V) shunt, is present; 

3) The application of the cuff on the wrist on the side of a mastectomy; 

4) Simultaneously used with other monitoring medical equipments on the same limb; 

5) Need to check the blood circulation of the user. 

8. 

 

This  Electronic  Sphygmomanometers  is  designed  for  adults  and  should  never  be 

used  on  infants  or  young  children.  Consult  your  physician  or  other  health  care 

professionals before use on older children. 

9.  Do not use this unit in a moving vehicle, This may result in erroneous measurement. 

10.  Blood  pressure  measurements  determined  by  this  monitor  are  equivalent  to  those 

obtained by a trained observer using the cuff/stethoscope auscultation method, within the 

limits  prescribed  by  the  American  National  Standard  Institute,  Electronic  or  automated 

sphygmomanometers. 

11.  Information  regarding  potential  electromagnetic  or  other  interference  between  the  blood 

pressure  monitor  and  other  devices  together  with  advice  regarding  avoidance  of  such 

interference please see part ELECTROMAGNETIC COMPATIBILITY INFORMATION.

                                                                         

 

12.  If Irregular Heartbeat (IHB) brought by common arrhythmias is detected in the procedure 

of blood pressure measurement, a signal of 

 

will be displayed. Under this condition, 

the  Electronic  Sphygmomanometers  can  keep  function,  but  the  results  may  not  be 

accurate, it

’s suggested that you consult with your physician for accurate assessment. 

      There are 2 conditions under which the signal of IHB will be displayed: 

1) The coefficient of variation (CV) of pulse period >25%. 

2) The difference of adjacent pulse period

0.14s, and the number of such pulse takes 

more than 53 percentage of the total number of pulse.   

13.  Please do not use the cuff other than supplied by the manufacturer, otherwise it may bring 

biocompatible hazard and might result in measurement error. 

14. 

The  monitor  might  not  meet  its  performance  specifications  or  cause  safety  hazard  if 

stored or used outside the specified temperature and humidity ranges in specifications. 

15. 

 

Please do not share the cuff with other infective person to avoid cross-infection. 

Summary of Contents for KD-723



















Reviews: