background image

ERROR CODE

Functionnalities

What this error mean and what to do

PT_LS

Measures the hydraulic system 
pressure

Can’t

read the pressure from the sensor.

Check if they are powered 12V by using a 
Voltmeter and testing the power from the 
connector. If no power, inspect powered wiring
for damage.

If 12V on the wire, sensor need to be replaced.

PT_SL_A

Measures the lifting system pressure (in 
order to provide weighing estimation of 
the bales loaded). Available on 2

nd

generation Stackpro only.

Can’t

read the pressure from the sensor.

Check if they are powered 12V by using a 
Voltmeter and testing the power from the 
connector. If no power, inspect powered wiring
for damage.

If 12V on the wire, sensor need to be replaced.

PT_CLAW or 
PT_PI

Read the pressure necessary to 
« squeeze » the bale in the loading arm 
grabber, before being lifted up

Can’t

read the pressure from the sensor.

Check if they are powered 12V by using a 
Voltmeter and testing the power from the 
connector. If no power, inspect powered wiring
for damage.

If 12V on the wire, sensor need to be replace.

LS_BA_SL

Detects if the bales has been dropped
on the loading table

Inspect the sensor

CLICK HERE

Search by “error code” what is the 

problem # 006

49

Scroll down for more error code on next page

Summary of Contents for STACKPRO 5400





























































Reviews: