manualshive.com logo in svg

Anderson STACKPRO 5400, Diagnostics Manual

Share
Download
Anderson STACKPRO 5400 Diagnostics Manual Download Page 25

25

CLICK BELOW

Functions

LS_BA_PI

Detects bales in the loading arm grabber. Initiate the loading sequence

LS_BA_SL

Detects if the bales has been dropped on the loading table

LS_DP_B

Detects when the unloading platform is at 

it’s

lowest position.

LS_CH

Detects when the rolling fork are pushed all the way back to the front

LS_DP_M

Detects the position of the unloading platform when reaching 45 degree in order to 
release the partial load to securely slide to the bottom of the platform / or when reaching
90 degree to prevent from over « pushing » the stack backward

LS_PD_R

Detects the unloading pusher when it is retracted

LS_PG_E

Detects the loading arm « wrist » cylinder when extended

LS_PG_R

Detects the loading arm « wrist » cylinder when retracted

LS_PO_R

Detects the bale pusher is retracted in stand-by position. The bale pusher move the bale 
towards the front on the loading table in order to make room for the next bale to come

LS_SL_B

Detects the loading table at 

it’s

lowest position

LS_SL_M

Detects when the loading table reach an angle of approximately 3 degree, before 
extending the table extension to the front

LS_SL_H

Detects when the loading table reach a vertical position of 90 degree. This sensor will
determiner how far the loading table will secure or not the bale between the side gate.

LS_ED_M

Detects the loading table extension toward the tractor according to the height of the bale 
choosen in the setting. This sensor is a magnet sensor, unlike all the other sensors that are 
proximity sensor design to detect steel.

LS_ED_R

Detects the loading table extension when it is retracted

LS_TS

Detects when the loading arm is in working position. That sensor need to detect steel
presence to unlock the loading mode of the touchscreen controller.

LOW OIL LEVEL

Detects a low oil level in the reservoir

OIL TEMP 
SENSOR

Detect the temperature of the oil in the reservoir

PT_CLAW or 
PT_PI

Read the pressure necessary to « squeeze » the bale in the loading arm grabber, before 
being lifted up

PT_LS

Measures the hydraulic system pressure

PT_SL_A

Measures the lifting system pressure (in order to provide weighing estimation of the bales 
loaded). Available on 2

nd

generation Stackpro only.

LS_BR_R,  LS_BR_E 
ARM ANGLE

Detects the position of the loading arm

Summary of Contents for STACKPRO 5400





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands