background image

MODEL A77 – REMOTE CONTROL AND WIRING

NOTE:

 Use 18-22 AWG wire for control wiring�

Humidity can be controlled using the internal dehumidifier control, a 
Model A77 control or a different external control like a thermostat�

Installing an external control eliminates the need to run the dehumidifier 
blower for sampling as the control is constantly measuring the humidity 
close to the canopy� When the humidity level rises above the setting, 
the dehumidifier is turned on�

To install and use the Model A77 control, complete ALL steps:
1. 

Unplug the dehumidifier or turn off power to the circuit at the 
breaker or fuse�

2. 

Run a 4-wire thermostat cable (use 18–22 AWG wire) from the 
Model A77 to the control of the dehumidifier�

3. 

Trim about 1/4" of insulation from the end of the wires on each end� 
Insert the wire into the terminals as shown in 

FIGURE 5

 and tighten 

to secure�

4. 

Restore dehumidifier power� There is a delay of three minutes after 
restoring power before the dehumidifier will respond to the control� 

5. 

Set up the dehumidifier to 

ENABLE REMOTE

 control as shown on page 7�

6. 

See 

USING THE MODEL A77 OR EXTERNAL CONTROL

 on page 7 for start up instructions�

The Model A77 will measure the relative humidity and turn the dehumidifier on and off to control the humidity level to the desired setting� The 
humidity setting can be adjusted from the control while the display allows easy access and monitoring of the humidity level in the space� It is 
recommended that the Model A77 be mounted at/near canopy height� Shield the Model A77 from direct exposure to HPS or LPS lighting�

Press the ON button on the Model A77 to turn on the control� The UP/DOWN arrow buttons are used to set the desired humidity setting� At all other 
times, the Model A77 will display the measured humidity level� Reference the Model A77 Installation and Operating Instructions for set-up�

ALTERNATE EXTERNAL CONTROLS

Alternatively, use any other humidity control system as long as it 
has a dry contact, normally open output dedicated to controlling the 
dehumidifier�

When using an external control, set up the dehumidifier to 

ENABLE 

EXTERNAL

 control as shown on page 7� Reference the installation 

literature provided with the alternative control for wiring, set-up and 
operating details�

+ - A B

ODT

Sensor

Remote

Gh
Rf
Cf

Gs

Y

W

HV

AC E

QUIP
.

DH

DH

R/+

C/-

B

A

MODEL A77 CONTROL

FLOA

T

DH

DH

SWITCH

EXTERNAL

CONTROL

90-1860

90-2542

FIGURE 5 

– MODEL A77 REMOTE CONTROL WIRING

FIGURE 6 

– ALTERNATE EXTERNAL CONTROL WIRING

6

Summary of Contents for A100F

















Reviews: