background image

User manual 

Guangzhou Andea Electronics Technology Co., Ltd. 

14/15 

http://www.gzandea.com     

Caution: The user is cautioned that changes or modifications not expressly approved by 
the party responsible for compliance could void the user's authority to operate the 
equipment. 

This device complies with Part 15 of the FCC Rules and Industry Canada 
licence-exempt RSS standard(s). Operation is subject to the following two conditions: 
(1) this device may not cause harmful interference, and   
(2) this device must accept any interference received, including interference that may 
cause undesired operation. 

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils 
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :   
(1) l’appareil ne doit pas produire de brouillage, et   
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si 
le brouillage est susceptible d’en compromettre le fonctionnement. 

NOTE: This equipment has been tested and found to comply with the limits for a Class 
B digital device,  pursuant to  Part 15  of the  FCC Rules.  These  limits are  designed  to 
provide  reasonable protection  against harmful  interference  in  a  residential installation. 
This equipment generates,  uses and  can  radiate  radio  frequency  energy  and,  if not 
installed and used in accordance with the instructions, may cause harmful interference 
to  radio  communications.  However,  there  is no  guarantee  that  interference  will  not 
occur in a particular installation.   
If this equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following measures:   
-- Reorient or relocate the receiving antenna. 
-- Increase the separation between the equipment and receiver.   
-- Connect the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the 
receiver is connected.  
-- Consult the dealer or an experienced radio/TV technician for help. 

FCC& IC Radiation Exposure Statement:

This equipment complies with FCC and Canada radiation exposure limits set forth for 

an uncontrolled environment. This equipment should be installed and operated with a 

minimum distance of 

20 cm

 between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other 

antenna or transmitter.

Déclaration d’IC sur l’exposition aux radiations:

Cet équipement est conforme aux limites d’exposition aux radiations définies par le 

Canada pour des environnements non contrôlés. Cet équipement doit être installé et 

utilisé à une distance minimum de 

20 cm

 entre l’antenne et votre corps.

Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne 

ou un autre émetteur.

Summary of Contents for RL865



















Reviews: