background image

 

 

 

 

VENTING REQUIREMENTS :

HEIGHT & CLEARANCE:

 

   •  Vent system must terminate to the outside 

      (Roof or side wall). 

   •  DO NOT terminate the vent system in an attic or        

      other enclosed area. 

   •  DO NOT use 4" (10.2 cm) laundry-type wall caps. 

   •  Use metal/aluminum vent only. Rigid metal/ 

      aluminum vent is recommended. 

   •  DO NOT use plastic vent. 

   •  Always keep the duct clean to ensure proper     

      airflow. 

   •  Calculate the following figures before installation: 

Distance from the floor to the ceiling 

Distance between the floor to the    

          countertop/stove 

Distance between the cooking surface to the    

          range hood (recommend 24" to 30") minimum of    

          30" is required for gas stove top 

For the most efficient & quiet operation: 

   •  A distance of 24" to 30" is recommended between     

      stove top and the bottom of range hood. 30" 

      minimum is required for gaz stove tops. 

   •  It is recommended that the range hood be vented     

      vertically through the roof through 6" (15.3 cm) or     

      bigger round metal/aluminum vent work. 

   •  The size of the vent should be uniform. 

   •  Use no more than three 90° elbows. 

   •  Make sure there is a minimum of 24" (61 cm) of  

      straight vent between the elbows if more than one 

      elbow is used. 

   •  DO NOT install two elbows together. 

   •  The length of vent system and number of elbows     

      should be kept to a minimum to provide efficient 

      performance. 

   •  The vent system must have a damper. If roof or   

      wall cap has a damper, DO NOT use damper (if 

      supplied) on top of the range hood. 

   •  Use silver tape or duct tape to seal all joints in the 

      vent system. 

   •  Use caulking to seal exterior wall or roof opening 

      around the cap. 

      1. 

      2. 

      3. 

      4. Height of hood and duct cover. 

 

 

Min : 24” 

 

 

 

 

Min : 24” 

Max : 30” 

Maximum ceiling clearance

100" at 30" hood mounting

height above countertop or

stove. (may vary with

different model). Chimney

extensions available for

higher ceiling 

36” base

Min:24”

Max:30”

Support

Structure

Standard

Upper

Chimney

Standard

Lower

Chimney

Range hood

Countertop/Stove

* Higher ceiling requires chimney extension.

Available at your local resellers

Model # 

 

Aero Island 36

5

Height of hood and duct cover.

Summary of Contents for Aero Island























Reviews: