background image

X-12

AnchorSpan™

Limited Warranty

Anchor Industries warrants that the AnchorSpan™ prefabricated building will be free of defect on 
material and workmanship.  We stand firm on our policy to correct any defect in the AnchorSpan™ 
or component thereof (including bearing the cost of freight in and out of Anchor Industries) dur-
ing the first year of use on fabric and three years on frame components.  Normal wear and tear or 
damage due to acts of God, exposure to chemicals, chemical agents or  improper installation are 
not considered to be defects.  All warranty repairs must be performed at Anchor Industries Inc., 
unless authorized by a company employee empowered to do so.  

Recommended Maintenance Tips

Fabric components should be cleaned as needed with mild laundry detergent and soft bristled 
brushes or mops and rinsed and dried thoroughly before being stored in the porous storage bags 
provided.  Store on shelving in a cool, dry area to allow full air circulation.  Bleaches, petroleum 
solvents and other caustic or harmful cleaning agents should not be used.  Aluminum components 
such as beam sections and purlins are maintenance free except for periodic surface cleaning 
to remove grit that may have gathered in channels during assembly or disassembly.  Steel 
components such as nuts, bolts, washers, baseplates and endplates for anchoring beams and 
fabric may require periodic maintenance in the form of sanding and repainting by the customer in 
order to prevent oxidation and realize their full potential life span.

Summary of Contents for AA AnchorSpan







































Reviews: