Anatomic SITT Zitzi Active User Manual Download | Manualshive

Page: 17 / 28

background image

17

User manual Zitzi Active

www.anatomicsitt.com | +46 11 16 18 00

Mounting the footrest

Mount the footrest in the square tube (A).
Secure the footrest with the locking
screw (B).

Adjusting the knee joint

Loosen the lever handle (C) and adjust
to desired position. Tighten when desired
positions is reached.

Important

- The tags have to fit with each

other. Lock the knob properly!

Height adjustment, foot plate

Loosen the lever handle (D), and adjust
to desired position. Tighten when desired
positions is reached.

Angle adjusting, foot plate

Loosen screws (E) for foot plate and
adjust to desired angle. Tighten screws
propertly.

Divided footrest, joint

A

B

C

D

E

!

!

= Adjustment bolts

«
...
15
16
17
18
19
...
»

Summary of Contents for Zitzi Active





























Reviews:

No comments

Related manuals for Zitzi Active

Brand: Pandhora Pages: 72

Brand: Invacare Pages: 12

Brand: Decon wheel Pages: 5

Brand: R82 Pages: 8

Ziggo Pro ZREC1200

Brand: Circle Specialty Pages: 4

Brand: Switch-it Pages: 2

Leon F Kameleon

Brand: Karma Pages: 136

Brand: Unicare Health Pages: 8

Brand: Levo Pages: 50

Brand: Comfy Go Mobility Pages: 24

Brand: Alber Pages: 9

Brand: Alber Pages: 48

Brand: B+B Pages: 63

Brand: Unwin Pages: 28

TGR-R KP-U 3522L

Brand: Timago Pages: 4

Brand: Timago Pages: 7

Brand: Timago Pages: 6

Brand: Timago Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands