Analog Devices EVAL-ADAQ4001FMCZ, User Manual

Page: 6 / 30

User Guide UG-1533
EVALUATION BOARD HARDWARE
analog.com Rev. A | 6 of 30
ANALOG INPUTS
The analog inputs of the EVAL-ADAQ4001PMDZ and EVAL-
ADAQ4003PMDZ , J1 and J2, are Subminiature Version B (SMB)
connectors. These inputs are fed to the ADA4898-1 . J1 and J2 are
buffered with dedicated amplifier circuitry, U4 and U7, as shown in
Figure 26 . The circuit enables different configurations, input range
scaling, filtering, amplifiers and supplies, and the addition of a
dc component. The analog input amplifiers are set as unity-gain
buffers at the factory.
The analog inputs are fully differential by default. If a single-ended
bipolar input is desired, such as ±10 V, the EVAL-ADAQ4001PMDZ
or EVAL-ADAQ4003PMDZ can be configured for single-ended to
differential conversion by changing JP6 to Pin B to Pin COM and by
applying the single-ended input at Connector J1 (see Table 2 ).
For dynamic performance, a fast Fourier transform (FFT) test can
be performed by applying a low distortion ac source. For low fre-
quency testing, the audio precision source, such as the SYS-2700
series, can be used directly with the evaluation boards. Different
precision sources can be used with additional filtering.
Table 2. Jumper Details with Factory Default Setting
Link
Default Function Comment
JP1 Not populated Gain options Fully differential or single-ended configuration.
JP2 B1 and B2, A1 and A2 µModule input The ADAQ4001 or ADAQ4003 has a gain of 0.454 (22 V range). See the
ADAQ4001 or the ADAQ4003 data sheet for other gains.
JP3 B1 and B2, A1 and A2 µModule input The ADAQ4001 or ADAQ4003 has a gain of 0.454 (22 V range). See the
ADAQ4001 or the ADAQ4003 data sheet for other gains.
JP4 Pin A to Pin COM Synchronize the switching frequency to CNV To set the switching frequency to 1.2 MHz, pull the SYNC/FREQ pin of
the
ADP5070 low or Pin B to Pin COM.
JP5 Pin A to Pin COM Op amp or in-amp Connect the J1 input to the ADA4898-1 op amp.
JP6 Pin A to Pin COM Op amp or in-amp Connect the J2 input to the ADA4898-1 op amp.
JP6 Pin A to Pin COM Single-ended or differential input Differential input by default. Connect Pin B to COM for a single-ended
input and connect JP7 to Pin B to Pin COM.
JP7 Pin B to Pin COM Op amp or in-amp Connect the ADA4898-1 op amp to the ADAQ4001 µModule or
ADAQ4003 µModule.
JP8 Pin B to Pin COM Amplifier or in-amp Connect Pin A to Pin COM to the output of the AD8251 .
JP9 Pin B to Pin COM Gain setting pin (LSB) Refer to the AD8251 data sheet for the truth table logic levels for
transparent gain mode.
JP10 Pin B to Pin COM Gain setting pin (MSB) Refer to the AD8251 data sheet for the truth table logic levels for
transparent gain mode.
JP11 Pin A to Pin COM Power Differential amplifier positive supply. Tied to ground.
JP12 Pin A to Pin COM Differential amplifier power mode Differential amplifier positive supply. Tied to ground.
JP13 Pin A to Pin COM Differential amplifier power down Normal mode. See the ADAQ4001 or the ADAQ4003 data sheet.
JP14 Pin A to Pin COM Reference buffer power down Powered up. See the ADAQ4001 or the ADAQ4003 data sheet.
JP15 Pin A to Pin COM Differential amplifier power down Powered up. See the ADAQ4001 or the ADAQ4003 data sheet.