EVAL-AD7761FMCZ User Guide
UG-949
Rev. 0 | Page 9 of 17
SOCKETS/CONNECTORS
Table 4. Connector Details
Connector
Function
Connector Type
Manufacturer/Part No.
Order No.
J1
Wall wart (dc plug) power supply voltage
input. Apply 7 V.
2 mm dc power
connector
Kycon KLDX-SMT2-0202-A
Mouser 806-KLDX-
SMT20202A
J2
Apply voltage within data sheet specified
ranges and GND (0 V) to this connector to
power the evaluation board. J2 is the
connector for supplying AVDD1, AVDD2,
IOVDD, AVSS, and AGND externally.
5-pin socket terminal
block
Lumberg FRE 05
Farnell 1217310
J3
Bench top power supply voltage input. Apply
7 V to 9 V and GND (0 V) to this connector to
power the evaluation board.
3-pin socket terminal
block, 3.81 mm pitch
Phoenix Contact MC
1,5/3-G-3,81
Farnell 3704737
J6
SMA/SMB connector for XTAL2 (CLKIN/LVDS).
Straight PCB mount
SMB/SMA jack
Tyco 1-1337482-0
Not inserted
J7
SMA/SMB connector for XTAL1 (LVDS).
Straight PCB mount
SMB/SMA jack
Tyco 1-1337482-0
Not inserted
J8, J9
8-pin connector for input to Channel 4 to
Channel 7.
8-pin socket terminal
block, 3.81 mm pitch
Phoenix Contact MC
1,5/8-G-3,81
Farnell 3704774
J11
Optional external connector for driver
daughter board to Channel 5.
7-way, 2.54 mm vertical
socket
Samtec SSW-107-01-T-S
Farnell 1803478
J12
Optional external connector for driver
daughter board to Channel 5.
7-way, 2.54 mm TH
header
Samtec TLW-107-05-G-S
Farnell 1668499
J13, J14
8-pin connector for input to Channel 0 to
Channel 3.
8-pin socket terminal
block, 3.81 mm pitch
Phoenix Contact MC
1,5/8-G-3,81
Farnell 3704774
J15
Unpopulated VCM SMA connector.
Straight PCB mount
SMB/SMA jack
Tyco 1-1337482-0
Farnell 3704737
AI0+ to
AI7+
Analog input SMA positive terminals for
Channel 0 to Channel 7.
Straight PCB mounts
SMB/SMA jack
Tyco 1-1337482-0
Farnell 1206013
AI0− to
AI7−
Analog input SMA negative terminals for
Channel 0 to Channel 7.
Straight PCB mounts
SMB/SMA jack
Tyco 1-1337482-0
Farnell 1206013
P1
Connection to
EVAL-SDP-CH1Z
controller
board.
160-pin, 10 mm male
VITA 57 connector
Samtec ASP-134604-01
Farnell 2433507
EVALUATION BOARD SETUP PROCEDURES
After following the instructions in the Software Installation
Procedures section, set up the evaluation and SDP boards as
detailed in this section.
Warning
The evaluation software and drivers must be installed before
connecting the evaluation board and
EVAL-SDP-CH1Z
board
to the USB port of the PC to ensure that the evaluation system
is correctly recognized when it is connected to the PC.
Configuring the Evaluation and SDP Boards
Connect the
EVAL-SDP-CH1Z
board to P1 (bottom) on the
EVAL-AD7761FMCZ
board.
Downloaded from
Downloaded from
Downloaded from
Downloaded from
Downloaded from
Downloaded from
Downloaded from
Downloaded from
Downloaded from
