Analog Devices ADRV9029 User Manual Download

Page: 35 / 82

Preliminary Technical

Data

Rev. PrA | Page 35 of 82

Figure 37. Direct EVM for the Best ACLR Performance

Observation Receiver Attenuation vs Stability Metrics

Shown below is the trend for the EVM and error stability metrics for different observation receiver channel attenuation values. It

can be observed that as observation receiver attenuation is increased, the error percentage also increases. The same might be

true for a low SNR transmitter to observation receiver channel. It is advised to increase the threshold for stability metrics as the

observation receiver attenuation increases or the channel SNR decreases.

Figure 38. ORx Attenuation vs. Stability Metrics

Observation Receiver Interference

Although unlikely, any interference in the observation receiver channel can cause DPD instability and can cause the firmware to

derive wrong DPD coefficients resulting in poor performance as shown below in Figure 39, which includes the bench

characterization of observation receiver interference levels affecting ACLR and stability metrics. Depending on the application

and the ACLR performance, the user can budget for the threshold of stability metrics. T1 represents the ACLR degradation at 5%

indirect EVM, and T2 represents ACLR degradation at 15% EVM. Data2 represents the absolute value of ACLR in dBm as the

power level of the interferer injected into the observation receiver increases. The total carrier power of the primary signal used

for characterization is 26.23 dBm.

Summary of Contents for ADRV9029



















































































Search results

Summary of Contents for ADRV9029

Reviews:

Related manuals for ADRV9029

Brands by name

Popular brands

Analog Devices ADRV9029, User Manual

Search results

Summary of Contents for ADRV9029

Reviews:

Related manuals for ADRV9029

Brands by name

Popular brands