background image

Introduction 

Landmark Cinema Quick Setup Guide 

 

Each of these steps are covered in the subsequent sections of this document. 

Landmark Cinema Components 

Before planning your Landmark Cinema installation, you should familiarize 
yourself with the Landmark Cinema components. This section introduces you to 
these devices. More detailed User Guides for each device are found in the 
Appendix of this document. 

PMB-CF2 Mini Cardframe 

The PMB-CF2 cardframe (Figure 1) holds two PHAST control cards. One is the 
PLC-MCU Master Control Unit, which is essentially a computer that runs on the 
Landmark Cinema's PhastLink network. The PLC-MCU runs the project code that 
is stored in its 2MB on onboard RAM. The other card used in the Landmark Cinema 
package is the PLC-IROUT IR Output card. 

 

Connection to the other Landmark Cinema components (except for the Viewpoint 
Touchpanel) is via a PhastLink cable that plugs into a PhastLink RJ-45 port on the 
rear of the unit. 

There are two PhastLink ports on the rear panel of the CF2. However, in a 
Landmark Cinema system, only ONE of the two PhastLink ports is available for 
use. The other PhastLink port must  be left unused. It does not matter which port 
you use. 

IMPORTANT!

    DO NOT terminate the unused PhastLink port. This port is already 

internally terminated when the CF2 is in "master" mode (when a PLC-MCU card is 
installed). Refer to the PMB-CF2 User Guide for more detailed information. 

 

Figure 1 

PMB-CF2 Mini Cardframe 

Caution 

Failure to comply with this 

restriction will cause the 

entire network to malfunction. 

Refer to the PMB-CF2 User 

Guide for more detailed 

information. 

Summary of Contents for Landmark Cinema

















Reviews: