background image

Landmark Cinema Quick Setup Guide 

Introduction 

 

The green LINK LED will blink in synch with the green DATA LED at the upper 
right corner of the rear panel of the PMB-CF2. This indicates that there is 
communication between the PLC-MCU card and the PMB-CF2 cardframe. 

The red DIAG LED indicates whether the Cinema project's program is running 
from the PLC-MCU's own onboard memory or from an attached PC. If the PLC-
MCU is operating from the program in its own memory, the red DIAG LED will 
blink briefly for 1/10 second in each second, something like a heartbeat pattern. If 
the PLC-MCU is connected to a PC and the program is running from the PC instead 
of the PLC-MCU, the red DIAG LED will blink on and off in equal 1/2-second 
intervals. 

The green LED on the PLC-IROUT card will only blink when sending an IR signal 
out from the card. 

PMB-TCC Television Control Center 

The PMB-TCC has four IR outputs on the rear panel, as shown in Figure 2. Each IR 
output connects to an IR emitter that must be compatible with whatever device(s) 
it controls. Connection to the PMB-CF2 is via a PhastLink cable that plugs into a 
PhastLink RJ-45 port on the rear of the unit. 

 

The green LINK LED on the front of the PMB-TCC (Figure 3) will blink in synch 
with the green DATA LED at the upper right corner of the rear panel of the PMB-
CF2. This indicates that there is communication between the PMB-TCC and the 
PMB-CF2 cardframe. The IR-OUT LED on the front of the PMB-TCC will blink 
whenever IR code is sent to an IR emitter from the PMB-TCC. 

 

Figure 2 

PMB-TCC Television Control 

Center (rear view) 

Summary of Contents for Landmark Cinema

















Reviews: