AMP Research PowerStep 77132-01A Installation Manual Download Page 1

www.amp-research.com

1/11

IM77132 rev 08.07.19

I N S T A L L A T I O N   G U I D E

 

        

3-5 Hours

Professional installation recommended

Invented, engineered and manufactured exclusively by AMP Research in the USA. May be covered by one of the following patents:  

6,641,158; 6,830,257; 6,834,875; 6,938,909; 7,055,839; 7,380,807; 7,398,985; 7,584,975   ©2012 AMP Research. All rights reserved.    

Printed in USA.

TOOLS REQUIRED

Safety goggles

Measuring tape

10 mm socket

13 mm socket 

                                

1/2” socket 

                  

Ratchet wrench and extension

Wire crimpers

 

Wire stripper / cutter

 

3/16” hex key wrench (allen wrench)

4mm hex key wrench ( allen wrench )

Electrical tape

Weather proof caulking (silicone sealer)

Silicone spray

5/32” Allen Key

INSTALLATION TIME

 

1 2 3

4

SKILL LEVEL

4= Experienced

AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2) Monday - Friday, 7:00 AM - 5:00 PM PST

APPLICATION   

 

 

 

 

 

 

                   

   AMP Part #   

 

Jeep  Wrangler  JL  4Dr 

                    2018  -  2019                                                                   

77132-01A                                                                   

5-Year Limited Warranty

WARRANTY

Summary of Contents for PowerStep 77132-01A














Reviews: