AMP Research Power Step 10-02996-13 Installation Manual Download Page 10

www.amp-research.com

10/10

A M P   R E S E A R C H   P O W E R   S T E P   –   F O R D   F 1 5 0   S U P E R C R E W

IM2996 rev 11.27.06

AMP RESEARCH warrants product to be free from defects in material and workmanship, for terms specified 
below, provided there has been normal use and proper maintenance.  This warranty applies to the original pur-
chaser only. All remedies under this warranty are limited to the repair of replacement of any item found by the 
factory to be defective within the time period specified.
 
If you have a warranty claim, first you must call our factory at the number below for instructions. You must 
retain proof of purchase and submit a copy with any items returned for warranty work. Upon completion of war-
ranty work, if any, we will return the repaired or replaced item or items to you freight prepaid. Damage to our 
products caused by accidents, fire, vandalism, negligence, misinstallation, misuse, Acts of God, or by defective 
parts not manufactured by us, is not covered under this warranty.
 
THE WARRANTY TIME PERIOD IS AS FOLLOWS: THREE YEARS FROM DATE OF PURCHASE.
 
ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE 
CREATED HEREBY ARE LIMITED IN DURATION TO THE SAME DURATION AND SCOPE AS THE 
EXPRESS WRITTEN WARRANTY. OUT COMPANY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR 
CONSEQUENTIAL DAMAGE.
 
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of 
incidental or consequential damages, so the above limitations or exclusions may not apply to you.
 
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
 
For further information or request for warranty work, please call toll-free 1-888-983-2206 (press 5) for 
Customer Service.

The manufacturer strongly recommends that this product be professionally installed.
 
Failure to carefully follow the electrical installation steps could result in severe electrical shock that could harm 
the installer and/or damage the vehicle.
 
This product is designed to enhance the appearance of the vehicle. Do not rely in any way on the components 
of this product to contain occupants within the vehicle, or to protect against injury of death in the event of an 
accident. Never operate vehicle in excess of manufacturer’s specifications.

WEAR SEAT BELTS AT ALL TIMES
 
Read and follow, precisely, all installation instructions provided when installing this product. Failure to do so 
could place occupants of the vehicle in a potentially dangerous situation. After installing or reinstalling, check to 
make sure it has been properly installed.

WA R N I N G

L I M I T E D   WA R R A N T Y

Summary of Contents for Power Step 10-02996-13











Reviews: