23
INDIVIDUAL FITTINGS
OPERATION, CLEANING AND MAINTENANCE
Before first use
l
After unpacking the appliance, make sure that the set includes all the attachments, and if there are no
visible signs of damage.
l
Before first use, wash in hot water all the attachments which come into contact with food. In addition,
thoroughly dry all parts before use.
l
Never immerse the body of the appliance in water or other liquids. This can cause damage to the mo
-
tor and pose a risk of electric shock.
l
Wash all food products before juicing. Cut large fruits, such as apples, into smaller pieces to fit into
the inlet.
l
Do not use frozen products.
l
Remove hard seeds and pits before juice extraction.
How to use slow-speed juicer
l
Expand the power cord, place the body of the appliance on a stable, dry and flat surface.
l
The order of assembly of individual components is shown on Fig. 2a.
l
Make sure that the rubber protective buffer is fixed on the pulp outlet hole at the bottom of the separa
-
tor container (Fig. 2b).
l
Make sure that the separator container gasket (Fig. 2i) and the juice outlet plug gasket (Fig. 2j) have
been installed correctly.
l
Place the separator container on the appliance body (Fig. 2a, item 1) in such manner that the two
ridges in the body fit into the grooves in the bottom of the separator container (Fig. 2c, item 2). Make
sure that the components are properly connected.
l
Connect the stainless steel filter with juice scraper (Fig. 2d).
l
Put the twoelement unit (filter and scraper) inside the separator container (Fig. 2f), bearing in mind
that there is a socket inside the container (partially covered by the protective buffer), which should fit
the edging in the filter (Fig. 2e, item 1). Make sure that the components are properly connected (Fig.
2f).
l
Insert the worm shaft in the separator container unit along with other fitted components (Fig. 2f). Make
sure that the worm shaft is properly secured on the drive shaft. Otherwise, the container will not close.
l
Close the separator container by putting the hopper on (Fig. 2g). Put the hopper on the vessel in
such a manner that the triangle symbol on the separator container and an open padlock symbol on
the hopper were in a straight line (Fig. 2f). Then turn the lid clockwise until it clicks into place. Make
sure that the elements are properly connected (the triangle symbol on the vessel and a symbol of a
closed padlock on the hopper must be aligned (Fig. 2g). Incorrect installation will prevent the start of
appliance.
l
Put the juice container under the juice outlet and the pulp container under the pulp outlet (Fig. 2h).
Before assembling the appliance, make sure that the power cord is disconnected from the wall
outlet.
1. Pusher
10. Juice outlet
2. Hopper
11. Juice outlet plug
3. Worm shaft
12. Appliance body
4. Stainless steel sieve (large mesh)
13. Control Panel
5. Stainless steel sieve (small mesh)
14. Drive shaft
6. Juice scraper
15. Pulp container
7. Cleaning brush
16. Juice container (1,000 ml)
8. Separator container
17. Juice scraper
9. Pulp outlet
EN
Summary of Contents for JSM 4011
