background image

22

RideMaxx Quick Start Guide

23

Finishing Installation

1.

  Without starting your bike, turn 

the  ignition  switch  from  OFF  to 

IGNITION.

2.

  Observe the three LEDs on the 

FuelMaxx ECU module: 

 —The red LED indicates your FuelMaxx 

has power. 

Flashing indicates activity.

—The blue LED indicates your Bluetooth 

enabled connection’s activity.

—The green LED indicates your Fuel-

Maxx is in wireless communication with 

your RideTuner. 

Note: This LED will only 

indicate when switching settings with your 

RideTuner.

3.

  Observe the LED on the RideTuner 

handle-mount module: 

—Press  either  the  PWR  or  ECON 

button to awaken the RideTuner for a 

blue indicator

(RideMaxx Auto). 

Note: A 

white indicator means the RideTuner is 

looking for the FuelMaxx module.

—Press the PWR button for a red indica-

tor 

(MaxxPower)

.

—Press the PWR button a second time 

to return to 

RideMaxx Auto.

—Press the ECON button for a green 

indicator

(MaxxFuel Economy)

.

—Press the ECON button a second time 

to return to 

RideMaxx Auto.

—The LED will remain on for 10 seconds 

until the RideTuner returns to sleep.

Finishing Installation

Testing your FuelMaxx and RideTuner modules

Using RideMaxx

The RideMaxx Auto, MaxxPower, and MaxxFuel Economy settings on the RideTuner

Two default pre-configured maps, per-

formance adjustment files, are installed 

as MaxxFuel Economy and MaxxPower. 

The third setting, RideMaxx Auto, does 

not  require  a  map.  All  three  settings 

eliminate backfiring and increase throttle 

response.

For further information on maps please see 

the 

Installing Maps

 section on 

page 24

By default RideMaxx will start in the Ride-

Maxx Auto setting when you start your 

bike. This setting will alternate between 

the economy and power settings depending 

on your throttle position.

The MaxxPower setting, once selected, will 

prioritize horsepower and acceleration.

The MaxxFuel Economy setting, once 

selected, will prioritize mileage.

When the FuelMaxx power LED indicates and the RideTuner toggles ride options (

see 

FuelMaxx green LED

) RideMaxx is fully functional. Replace your seat and bolt (

Softails

or cowling and saddlebag (

Baggers

). 

Congratulations, RideMaxx is installed!

Note—RideMaxx will always start in the RideMaxx Auto setting when you start 

your bike unless configured otherwise with the included software. Once the RideTuner 

is asleep, any button press will awake it and indicate the current setting.

Summary of Contents for RideMaxx


















Reviews: