manualshive.com logo in svg

Ametek VERSITRON BT130R, Operation Manual, Page: 11 / 82

Share
Download
Ametek VERSITRON BT130R Operation Manual Download Page 11

Versitron Operation Manual 

11 

 

4.0

 

INSTALLATION AND SETUP

 

4.1

 

Test Stand Installation 

The Versitron machines are heavy machines and great care should be taken in 
choosing the location where is to be installed. Ensure the bench is capable of 
remaining firm and stable withstanding the combined weight of the machine and any 
accessories supplied. Please see the Specifications page (section 7.0) for the weight 
of the apparatus.  

Suitable lifting equipment should be used when lifting the Versitron machine; i.e.  a 
hydraulic floor hoist (2t capacity, recommended) and a polyester sling (5t. rating, 
recommended). Please ensure outmost care is taken when lifting this instrument, use 
safe working practices. 

 

The 

tester is shipped in two crates, one containing the Stand with an Accessory Kit 

and one containing the Test Head

. 

Included in the Accessory Kit should be: 

• 

Set of Allen wrenches

 

• 

2” Vee anvil

 

• 

Spot anvil

 

• 

Test blocks

 

• 

Wrench to remove elevating unit

 

• 

Pin wrench

 

• 

Small Vee anvil

 

• 

1/16” ball indenter

 

• 

Anvil base collet

 

• 

Calibration block

 

• 

Vinyl protective cover

 

 

Lifting the Versitron machine 

(AT130N shown) 

Ensure the sling is 
wrapped around this 
area of the machine 
(as shown).  

Summary of Contents for VERSITRON BT130R



















































































Reviews:

No comments