Ametek Land LSP Ex System User Manual Download Page 31

Page: 31 / 48

Page 21

User Guide

LSP Ex System for Zone 22

Linescanner Head

3 Services

3.1 Electrical connections: Cable requirements

The connection between the Hotspot IR Ex Head and Landscan Processor is via a

12-way cable.

Warning

Cables must be installed such that they are protected from mechanical

damage and strain.

Four pre-wired cable assemblies are available from LAND:

LAND Part Nº

Length

Sheath material Ambient limit

Overall diameter

031-402

15m / 49ft

PVC

80°C / 176°F

11mm / 0.43in

031-794

15m / 49ft

Teflon

200°C / 392°F

6.8mm / 0.27in

802406

50m / 164ft

PVC

80°C / 176°F

11mm / 0.43in

Note

There are limits to the cable length that each processor is able to operate

with the LSP head.

The table below summarises these limits.

Cable Function

LSC_C

LSC_B

POWER

15m / 49ft

150m / 491ft

DATA 031-794

300m / 984ft

(Fast temperature, Scan Valid, IATS, Emissivity)

If the installation requires the distance between the LSP Head and the LSC

Processor to be greater than that indicated in the above table, a local 24Vdc

power supply must be used.
Land recommends the use of the following Power Supply:
•

Terminal box with power (Land Part Nº 802662)

Summary of Contents for Land LSP Ex System

















































Search results

Summary of Contents for Land LSP Ex System

Reviews:

Related manuals for Land LSP Ex System

Brands by name

Popular brands

Ametek Land LSP Ex System, User Manual

Search results

Summary of Contents for Land LSP Ex System

Reviews:

Related manuals for Land LSP Ex System

Brands by name

Popular brands