background image

238-45839-00D  REV 07/07 

DIRECT VENT GAS WATER HEATER 

 

 

 
 
 
 
 

 
 

 WHAT TO DO IF YOU SMELL GAS 

• 

Do not try to light any appliance. 

• 

Do not touch any electrical switch; do not use any 
phone in your building. 

• 

Immediately call your gas supplier from a neighbor’s 
phone.  Follow the gas supplier's instructions. 

• 

If you cannot reach your gas supplier, call the fire 

 department. 

 

Installation and service must be performed by a qualified 
installer, service agency or the gas supplier. 

 
For your family’s comfort, safety and convenience, it is 
recommended this water heater be installed and serviced by a 
plumbing professional.

 

INSTALLATION & OPERATING 

INSTRUCTION MANUAL

 

WARNING:

  If the information in these instructions is 

not followed exactly, a fire or explosion may result 
causing property damage, personal injury or death. 

FOR YOUR SAFETY 

 

   Do not store or use gasoline or other flammable, 

combustible, or corrosive vapors and liquids in the 
vicinity of this or any other appliance. 

A Spanish language version of these instructions is available by contacting the
company listed on the rating plate. 
La versión espãnola de estas instrucciones se puede obtener al escribirle a la
fábrica cuyo nombre aparece en la placa de especificaciones.

 

Summary of Contents for DIRECT VENT GAS WATER HEATER









































Reviews: